Hire a trusted appliance repair service in Sydney

What I need: • Diagnose the cause of the drainage issue • Repair on the spot if possible (e.g. blocked filter, drain pump, hose) • Advise if parts need to be ordered Details: • Appliance: LG dishwasher • Issue: Not draining – water pooling at the bottom

2 draw fisher & Paykel. Board stopped rotated from spinning and caused F1 error need to reset . Bottom draw still works fine.

Fisher & Paykel fridge alarm & light won't turn off

Hi there, looking for an experienced appliance technician to repair my 3-year-old LG fridge. Symptoms • The internal lights are working. • I can hear the fan running in the back. • However, the compressor doesn't seem to be kicking in and everything has completely defrosted. It might just need a new start relay or thermostat. Please let me know your call-out/diagnostic fee and your availability.

Dishwasher leaking/foam error Washing machine doesn’t run full cycles, error halfway though spin

My oven is over heating. Set at 125 the temperature goes to over 300. It’s a calibration or temperature probe. The oven is a ILVE T906WMP

The dish washer is not working and might be blocked

Suspect fuse blown in clothes dryer. Power just cease working when washing machine was going. They share the same double power outlet. I've tried other power outlets in the house and still won't turn on.

Hi, I’m looking for someone experienced with Fisher & Paykel DishDrawer dishwashers to diagnose and repair my current unit. Model: Fisher & Paykel DD60SDFX9 Product code: 81215-C Serial: NHG279757 Issue: the dishwasher is not draining properly. There is standing water at the bottom, and when powered on it makes a very loud whirring/fan-like noise. I’ve already cleaned and checked the filter/pump area multiple times and can’t see any obvious blockage. Possible issue seems to be either: * blocked drain path / hose / sink connection * jammed or failed drain pump / rotor / impeller * possible flood sensor / leak fault state I’m looking for someone who can: 1. Diagnose the issue properly 2. Check the drain hose, sink connection and pump/rotor area 3. Confirm whether it needs a drain pump/rotor replacement or another part 4. Repair it if possible, ideally on the same visit if parts are available Please only offer if you have experience with Fisher & Paykel DishDrawers or similar dishwasher repairs. It would be great if you can mention whether you can source parts, and your availability. Location: Kings Cross, Sydney Timing: as soon as possible / flexible

Dishwasher is leaking from the front, sometimes it gives the E4 code, nothing was shown this time. Looking for someone to diagnose and repair the problem, as well as check for water damage under/behind the dishwasher, which might include pulling it out and re-installing after.

dishwasher model： Miele G4203i Problem： Error code F11 Has followed the instructions to remove and clean all the parts that might cause the issue but the code still on. The hose may be alright of partially blocked as when we tried to run the program the water can be drained out at the beginning and the F11 code appears in the middle of the process. There might be something wrong with the pump or the electric panel.

Our Bosch series 8 front loader washing machine seems to be turning on but the display panel is not working. Require someone to possibly fix this if it’s worth fixing rather than buying a new machine. Located Petersham, 2hour street parking only. Today would be ideal.

Clean all drain hoses, clean filters, clean inside of the dishwasher.

Schweigen Rangehood unable to power on or off the buttons are not working, it is a connection issue as the light is working but the button for.on and off isn't

My dishwasher works but I think needs to be plumbed / installed properly.

Curling iron I bought in France . I think the cord was wound too tight and the wires have come loose . If easy would like to have cord /plug replaced to an aussie plug

Wire has detached from washing machine

Samsung laundry washing machine repair - when in rinse cycle machine starts spinning and makes loud noise sounds like the drum is hitting against the door.

I have an Asko dishwasher mounted under the bench - a couple years old - and it’s giving an error code - F12 - when I try to run it. It’s done this in the past and always resolved itself but this time it’s being stubborn. I’ve looked it up, I understand what it’s saying but I just don’t have the tools or experience to fix it. It seems like a quick and simple job for someone who does.

I just had my new dishwasher installed and the tap under the sink where it is connected to is leaking. The installers said it might be a corroded washer inside the tap.