Hire a trusted appliance repair service in Glebe Point

Breville Touch Impress is not grinding and making a loud noise. I believe it may be an issue with the upper burr grinding part.

Need to fix the small deep fryer once we turn on pilot is on and flame goes on as well while we set the temperature to 180 flame turns off before reaching the temperature and it goes on again. It turns on and off itself before reaching the set temperature but temperature is not constant.

Fix washing machine with alarm error E:23. Bosch Series 8 machine.

Water leaking out from under machine - likely just need someone stronger than me to pull machine out of cavity & check hose at back.

Integrated Fridge not working and sounding alarm

Dryer is only just over a year old. Won't turn on.

Hey mate, Do you fix these? Job located in glebe. The power is tripping randomly the powerboard circuit not always but say once or twice a day from this unit

Water not draining after washing cycle

The fridge is cooling, but not cold enough. The freezer is still working fine, ice is frozen. It was turned off for 3 months while on vacation. Came back and it was working fine for the last few days but woke up this morning to the temperature not being cold enough and the milk having gone bad. Could be a fan problem. The compressor is warm and humming from what I can tell. The fridge made a few clicking noises the first day when it was turned on. There was also a slightly musty smell for the first few days which I thought it was just due to to disuse, but it might be a gas leak.

La Morzocco PB 3 group machine to be installed/repaired. I purchased a machine from a shop which was working. Now it's at my shop, electrician has hard wired it (but didnt run proper tests)and plumbing is done. The machine won't start at all. No lights, nothing. I don't know if it's an electrical issue or a machine fault. I'd prefer if someone could do electrical and repair in case one or theft her is needed.

Door has snapped off white plastic bit in door is not there

When the dishwasher cycle gets really hot it opens up and stops. We think its related to the seals or latch not working well? We tried sticky taping it shut and that works, no real issue when it remains closed. We need someone that has an idea of how to fix this? Someone with experience in Bosch? Model number: smu50e75au/59

I need an experienced appliance repair technician to diagnose and fix an electronic fault on a Sôlt front-load washing machine that is showing the E50 Error Code. Machine Details: • Appliance: Sôlt 8kg Front Load Washing Machine • Model Number: GGSFLW800W Problem Summary: The machine initially experienced a mechanical jam when the front door seal (gasket) clamp became dislodged. The drum now spins freely by hand, but when any cycle is started, the machine displays the E50 fault code and will not start the motor or drain the remaining water. The fault is electronic, not mechanical. What I have checked: • The Front Door Seal Clamp has been correctly re-seated. • The Drum spins freely by hand (Bearings/Major Jam is clear). • The Drive Belt is visually intact and correctly seated on the pulleys. • A 15-minute hard power reset has been performed, but the E50 error returns. • The back panel is currently unsecured for easy access. Likely Required Repair (Based on Diagnosis): The fault is likely one of the following, which will need professional inspection: 1. Motor Carbon Brushes: Worn out and unable to provide enough torque after the sudden stop. 2. Tachometer/Speed Sensor: Damaged by the shock of the jam, preventing the motor from getting speed feedback. 3. Main Control Board (PCB) / Triac: Component failure caused by the current surge during the jam. Offer/Pricing: Please provide a quote that includes the following: 1. Call-out and Initial Diagnosis Fee. 2. Labour and Parts for the repair (if possible, provide an estimate for replacing the brushes/sensor versus the cost of replacing the PCB). I am seeking a technician who has experience with Sôlt, Electrolux, or similar Asian-made front loaders. Please state your relevant experience when quoting.

Error E:36 - 10. I somehow managed to wrap a lightbulb into my bedding which went into the wash. It's now not draining water, and I've done all the steps to try and remove the fragments that I can but there's clearly a bigger issue. It's a BOSCH washer/ dryer combo

I have a washing machine that needs a single Part replaced electrolux ewf12832 door lock . I have purchased the spare part and need it installed

The washing machine door handle has broken and I cannot open the door. It broke as I was trying to open the door after the wash cycle had ended and now the door is stuck shut with my washed clothes inside. I will require a handyman to please help to fix this, it will likely also need a door handle replacement. The machine is the Simpson swf10761, I have attached photos below.

Replace Door Seal - Fisher & Paykel WH9060P4 Door seal on my 9kg front loader washing machine is leaking and needs replacement. I already have the replacement seal - just need someone to install it. Scope of Work: - Remove old door seal/gasket - Install new door seal (provided) - Test washing machine to ensure no leaks - Clean up any water spillage during repair Requirements: - Experience with washing machine repairs - Bring your own tools Timing: - I work from home. Can be flexible on time of day. Sooner the better.

My Omega Dishwasher make a rather loud noise when it starts the draining cycle, and will not drain. Therefore I have stopped the diawasher and left it undrained. Make: Omega Model: ODW300XN I'm looking for someone who can inveatigate the issue with the dishwasher and fix it.

We are looking for someone to fix our dishwasher. It's Bosch series 6 silence plus. I believe the pump might need replacing.

haier washing machine door is not closing - need a specialist to come do on site repair