Hire trusted appliance installation services in VIC

I have a 90 cm slide out rangehood over a gas cooktop. The wall immediately behind the cooktop is an external wall. I want to replace the existing Technika range hood with a mistral 90cm of the same size slide out range hood. I want 150 mm rigid ducting going directly through the external wall, and absolutely no exhaust into the roof cavity.

Hi, Needing someone to install glass into pullout kitchen rangehood. Would need to use heat resistant glue/silicon. I have the piece of glass, just need someone to install and bring glue/silicon required for job.

Please let us know how much you will charge for the following: - Installation of a rangehood unit in place of the old unit. Old unit has been removed and wall is ready for the new unit to go on. - Rangehood will be supplied upon purchase and delivery (within the next few days or a week depending on delivery - It will be a basic inexpensive wall mount ducted canopy unit. - Duct already in place. Only needs to be put up on the wall above the stove onto plaster board, the duct connected to the unit, plugged in and ready to go. - There is a tiled splashback but the unit will be installed where the tiles stop and plaster board starts. - Most likely no cutting of the flue will be required to adjust the length. If cutting is required it would minimal. - The space between ceiling to the tiles is 790mm and the units we have looked at are within the range.

install replace new oven remove old ovens wire up new ovens

I have a Fotile range hood with a 170mm exhaust. I need someone to supply and install 200mm rigid ducting vertically about a metre onto the roof to connect to a provided 200mm exhaust vent. It is a two storey property but this part is on the first storey and accessible by ladder. Roof is concrete tiles. Will need someone who is a licensed roof plumber.

I have a hair dryer the cord has split it needs cutting and resoldering are there any repairers around that can do this. Thanks

I have a hair dryer the cord has split it needs cutting and resoldering are there any repairers around that can do this. Thanks

I need the existing 90mm range hood removed and a new Devanti 90mm range hood installed (https://www.bigw.com.au/product/devanti-900mm-range-hood-90cm-rangehood-stainless-steel/p/9900145639)

Ideally a licensed plumber to help extend the grey water hose of my washing machine to reach where it needs to go and install it the grey water outlet. I have done a little bit of research and I believe I have all the supplies required - including the extension hose, hose clamps and joiner connections (see photos) *theres a Bunnings around the corner if not Hoping this will be a relatively easy job for someone that knows what they are doing. However, I do require the tasker to provide their own tools, which includes a drill and potentially some to cut the hose to the correct length if required. (This is a new build and it doesn't look like the hole for the grey water outlet is opened yet) **IMPORTANT NOTE - i am the tenant and not the owner, so no major changes to pipes or anything else can be made for this job.

I want someone who can remove the existing slideout rangehood which is connected to a duct as their is a vent outside and install a new slide out rangehood. Same size, nothing different just a new one.

The task involves removing an older 60cm Smeg Rangehood (SA480T) and installing a new 60cm Smeg Rangehood (STH600X1). I need to avoid modifications to external cabinetry. Internal adjustment, that is not visible, is okay. I have shown the specification for each rangehood in the pictures. Both rangehoods have the same dimensions, however I am not sure if there will be any issues with the existing duct diameter and duct hole position. See the attached pictures / photos which has dimensions / specifications. Location is an apartment building on St Kilda Road, Melbourne 3004.

I m looking for an certified electrician to install new oven and provide Certificate of Electrical Safety We have 20A switch breaker already. Current oven is hardwired and new one will require hard wiring the same cables I have attached photos of the switch breaker, current wiring and how its currently hardwired Current oven is 10A We are planing to install 15A oven I believe we need to install rcbo as well Expecting delivery in 3 -4 days so install needs be later next week or early following week

Remove the existing rangehood and install the new one. Simple model 60cm slide out rangehood

Please install a 60cm cooktop. You will need to remove the existing cooktop and dispose of this. I need this done asap

I have a toaster that runs on 15amp but requires a repair (see attached)

My appliances are all functioning, but I sense they lack pep and need some technical TLC. The filter for the washing machine needs to be unscrewed and cleaned, the dryer needs a check over and the dishwasher isn’t cleaning the bottom drawer like it used to, though everything seems in order. Brands and models are shown in the photos. I’m only wanting qualified appliance technicians.

Our drive belt for our washing snapped. Ive bought the replacement part but cant get it on for the life of me. Need some help. Then also need a quick hand to put the dryer back on top of it. If the job could be done today or tmw would be great

I need a licensed electrician to install the oven. The old oven has been removed already. Oven being installed: Bosch Series 4

Removed old range hood have a new one needs to be installed needs to be drilled and secured through stone splash back

I need the kitchens oven fan to be routed externally as it is inside the ceiling at the moment