Hire trusted appliance installation services in North West Melbourne

Gas heater to be installed with pipe

Removed old range hood have a new one needs to be installed needs to be drilled and secured through stone splash back

We have our kitchen exhaust installed, and working, just need to have a vent to go to the outside through a weatherboard wall.

Install linaire 40cm island rangehood. All electrical works are already in ceiling/roof

We currently have single phase but were told to install electrical cooktop n oven we need a separate socket n eliminator.

Repairs the sandwich counter. The temperature is colder

Induction cooktop has been delivered. A small adjustment to the wooden bench opening is required to properly seat it. 15A lead is pre-wired to the cooktop but leads need terminating in a 15A plug. 15A outlet is installed and ready for use, as this is a replacement cooktop.

Old Vulcan oil heater to be replaced with digital display heater

Hi guys I need a new electric oven installed replacing an old one. Same size. Location Gisborne

I need someone to install an inducton cooktop and remove the old one Estimated : 30 mints job

Technika oven needs new door hinges and door seal. Job in lalor

Bosch series 6 Washer/dryer Need new gasket installed Gasket has already been purchased and ready to be installed

Looking for an experienced installer to complete the roof flue installation only for my rangehood. Flue kit: Pacific Air 150mm tiled roof vent kit Location: Kitchen rangehood already installed and ducting accessible in ceiling Job required: - Cut roof tile and install flue through tiled roof. - Install flashing and roof cowl Seal/caulk properly to ensure it is fully waterproof. Notes: - Single storey home - Easy roof access - I will supply the flue kit - I will supply caulking. - I will connect the duct to range hood itself Looking for someone with experience in roof penetrations and sealing (no leaks). Thank you

Electrician to install a 600mm Robinhood range hood in Glenroy. Vent through the ceiling or wall.

Hi, I am seeking an electrician to install and hardwire a 900mm freestanding Westinghouse oven. Duel fuel however gas fitting to be done separately. To be done either Sunday or Monday. Model: https://www.thegoodguys.com.au/westinghouse-90cm-dual-fuel-freestanding-cooker-wfe9515sd?utm_pmaxpaidsearch&gclsrc=aw.ds&gad_source=1&gad_campaignid=20288282065&gbraid=0AAAAACuCjWVdMfNXQIAnBatKWid6nMvyu&gclid=CjwKCAjw687NBhB4EiwAQ645drtIgGpVPxSuNH1gLHlPhM_rZW91CVN2SenHmx2j9uWPO405gVNDQxoCi_kQAvD_BwE

Needing a electrician to install a new rangehood. Ready to go current one taken out just need it installed. Also need a eufy door bell installed (hardwired) Range hood and door bell all supplied just need them both fitted.

Replace the below rangehood

I need a slide out Rangehood installed to replace an existing one that’s broken. I also have some electrical work like light switches to be replaced.

Install Westinghouse WRR904SB (90cm slide-out, stainless steel trimmed front, model WRR904SB). Location: Under-cabinet recessed space (IKEA-style cabinetry). Measurements: Recess opening ~890 mm wide; available depth 300 mm; height clearance sufficient (product height 175 mm). Mounting: Slide-in under-cabinet fit (secure to cabinet sides/top/bottom with screws/clips; removable front fascia for integration if needed). Ducting: Rear venting required (no top space available). Hood has rear duct hole option (120 mm diameter outlet). Connect to existing angled rear vent path Install new WRR904SB (I will supply the unit). Connect rear ducting (Hood has rear duct hole option (120 mm diameter outlet). Connect to existing angled rear vent path (trapezoidal, narrowing to ~140 mm with 160/140 mm sides). Use 120 mm (or 125 mm with adapter) semi-rigid/rigid duct, short elbow/bend, clamps, and foil tape for airtight seal.) supply install ducting part or can purchase the required before install Power: to be connected by installer

install support chains to 90cm dual fuel upright stove