Find trusted insulation contractors in VIC

3 bedroom house Reno. Block construction. Need insulation

I’m looking for some help to remove all unnecessary wires, old pipes, loose debris etc from underneath our house. Then raking/levelling the ground to remove rocks & create better access & a clean area for underfloor insulation to be installed. Happy to pay a day rate & I will work alongside you, until the job is done as I’m unsure how long it will take.

Need old pink bats removed and debris vacumed. Waste despose of. Ground floor house about 120sqm

My garage is 3.1 x 6.3 and I need three walls (with budget insulation) framed along with a ceiling. I will paint them myself and I have an electrician for the lighting. My price is for labour. I will pay the additional price for materials when needed.

bradford r5 ceiling batts will be delivered soon. Needing a hand with 115 square meters of roof insulation laying. Must have prior experience. Looking for a solo labourer as I also have experience in insulation

Hi! Reinstatement of 1.5 m² of internal façade wall lining following completed mould remediation. Supply and install insulation matching existing specification, reinstate plasterboard, tape and finish ready for painting, and reinstall approx 2.5 m of skirting (we have already bought the skirting for under the window). No demolition or structural work required. This is an apartment in a larger building. On site parking available, lift available. Separate air-tasker jobs not included (but check-out our other post about this) : 1- Carpet re-instatement (we saved the carpet that was new that now needs re-laying) 2- repaint (primer and paint supplied)

Install of underfloor insulation, 105 square meters worth. We will supply the insulation.

Hi, I'm looking for someone to remove my existing ceiling insulation and install new R6.0 insulation batts. The property is a double-storey house in Clarinda. Est. 90sqm. Could you please provide a quote including materials, labour and removal/disposal of the old insulation? Thanks!

There is a room in the house with no ceiling insulation, which needs to be installed. I want R6, quote me for your labour, and install (including getting the insulation), and I will pay the invoice for the insulation. Flexable with timing, but would like to be done within the next 2 weeks

After insulation and wrapping for new house in Tarneit

Garage door insulation to cover pest gaps

I would like to install plaster board wall and ceilings with insulation at my garage. Currently sides are just asbestos sheet, not any wall. Am getting rid of those sheets. Ceiling is just tin sheet. Measurement is 3.6x10.7. You need to install frames as well.

I need someone to install about 50m2 of underfloor insulation. This is about half the house, the other half is already done. The clearance varies between about 45-55cm, but there is a fair bit of old building waste and rubble. The entrance into the underfloor area is smaller at about 35high to 55cm wide. The batts are on site in the black bags in the pictures. Fairly straight forward. I have already done the ceiling insulation and some of the underfloor myself. This is all that's left.

R5.0 insulation required to be installed in roof of our two-bedroom unit in Hawthorn. Only small amount of insulation required on edges of house where previous installer failed to do so. Also required to supply the insulation - will reimburse on top of the installation fee.

I’m looking for an experienced carpenter / plasterer or ceiling renovation contractor to install a new insulated plasterboard ceiling in my existing single garage in Malvern East. Garage details: * Approx. 3.5m × 6.1m (21m²) * Existing corrugated metal roof with exposed timber beams * No existing plasterboard ceiling * Roof has been inspected and repaired, with no active leaks identified * Electrical rough-in has already been completed for 6 LED downlights Scope of work: 1. Inspect the existing timber beams, particularly one partially deteriorated section near the rear window. Advise whether additional timber reinforcement is required and provide a separate price if necessary. 2. Supply and install suitable ceiling framing/battens as required. 3. Supply and install ceiling insulation, including an appropriate condensation-management solution for the existing metal roof. 4. Supply and install plasterboard ceiling across approximately 21m². 5. Complete all plasterboard jointing, stopping and sanding, ready for painting. 6. Construct a suitable bulkhead/boxing around the front roller door area and close fixed gaps where appropriate, while maintaining full roller door operation and service access. 7. Allow for the 6 pre-wired LED downlight positions. Optional extra: * Weather sealing around the roller door, including top and side brush seals, if experienced with garage doors. Important: * The electrician will return to complete the LED downlight installation. * Please include labour and materials in your quote. * Please specify whether timber reinforcement, insulation, bulkhead and sealing are included or priced separately. * Photos of the existing garage are available. Looking for someone experienced who can manage the complete ceiling installation from framing through to a paint-ready finish.

Remove (only) roof insulation from a small 3 bedroom home in Ivanhoe on Saturday morning. Ceiling has been removed in kitchen so easy to use to drop insulation on the kitchen floor and then place outside for rubbish collection. Only partially insulated with some patches of no insulation in ceiling.

I need a fit and motivated Tasker to crawl under my house on stumps and shift some dirt to the side.The spray foam insulation guy has completed 70% of the subfloor, but needs a narrow crawl space cleared in the last 30% tight corner so he can fit through to finish the job.$50 an hour

Install R2.5 polyester insulation under the floor of a 2 bedroom weatherboard house (approx 85sqm) (will provide insulation, staple gun, coveralls, dust mask and sheet to lie on if you need)

I’ve already installed over half the subfloor insulation in my home (134m2) and need someone to complete the job (approx 65m2). The product is a recycled polyester batt (soft, no itch, no PPE needed) that simply tucks up between the joists and staples into the timber, very straightforward once you’ve done a few. The work involves: • Cutting rolls to length (width is pre-sized, length cuts only) • Tucking batts snugly up under the floorboards • Stapling into timber joists to secure Important: There is fragile ducted heating pipework under the house. You’ll need to work carefully around this and not rush. This is the main requirement, someone methodical who won’t damage the ducting. It’s not difficult but it is a little tedious and dirty under there. All equipment is provided: • Knee pads • 2 x staple guns • Head torch • Scissors/blade for • Protective eyewear and mask (for dust) •I used a bike helmet to protect my head which you are welcome to use but if you have a hard hat that would be better. You’re welcome to bring your own gear if you prefer. The insulation rolls are on-site and ready to go. I’ll show you what’s been done already so you can match the approach. Product reference and install method: https://youtu.be/-rIyo6bh9A4?si=hNoCcayYgbWn_9LT Please only apply if you’re comfortable working in a crawl space and can commit to careful, unhurried work. Happy to answer any questions.

I’m looking for some help laying the insulation layer for my single-story house. I already have the insulation rolls on-site.