Find a professional gate installation near you

Automatic gate installation only Scope of works Weld existing double gate to single gate Pour concrete plinth Install D5 evo smart per operation manual All material supplied

I need an experienced gate installer to supply and install a new automatic sliding gate at my house in Rowville (3178). The job: Sliding gate across the driveway opening, roughly 5 m wide. Please measure on site. Pedestrian door built into the gate. The gate sits in line with my existing grey timber front fence. When it opens, it slides right and parks behind that fence. The fence stays. Its end post will need to be replaced with a steel guide post. Black powdercoated aluminium horizontal slats, about 1.8 m high to match the fence. Motor on the inside at the fence end, with 2 remotes, safety beams and battery backup. Please include in your offer: Gate, posts, track and installation Motor and safety devices Fence end post change Electrical work, or let me know if I need my own electrician Lead time and warranty Photos of similar gates you’ve installed I’ve attached a sketch and photos of the frontage. A site visit to measure is welcome. I’m checking with council before the job starts, so the start date depends on their advice. Location: Rowville VIC 3178 (in person) When: Flexible, ideally within the next 4–8 weeks

Program brand new sliding gate motor . Gate and motor are installed . New motor fitted but need it programmed. Has been operational for past ten years.

Installation of Solar Automatic Gate Opener – Existing Farm Gate Looking for someone experienced in installing solar-powered automatic gate opening systems to install a new Lockmaster solar swing gate opener on our existing farm gate. We have already purchased the equipment, including: * Lockmaster single swing gate opener with 40W solar panel * 2 x wireless keypads * Automatic electric gate lock (24V) * Infrared safety sensors Scope of work: * Install and set up the solar gate opener on our existing farm gate * Mount and connect the solar panel and control unit * Install and configure the wireless keypads, electric lock and safety sensors * Program and test the system to ensure everything operates correctly * Advise if any additional brackets, posts or fittings are required Experience essential: We are looking for someone who has previously installed automatic gate opening systems, ideally Lockmaster or similar solar-powered systems. Please provide details of your relevant experience, availability and a quote for installation. Photos of the existing gate and equipment can be provided.

Looking for an experienced gate installer to supply and install a new automatic gate opening system with remotes, for our existing aluminium gates.

need a quote for installing solar automatic sliding aluminum gate

Swing gate at my property has broken down. Will need a quote to repair them.

on site quote on automatic gate....

I need a new automatic gate opener installed that is solar

Looking for an experienced automatic gate technician to inspect and repair a solar-powered automatic driveway gate. The gate is currently not operating correctly and needs troubleshooting to identify the issue, which may involve motor, controller, sensors, remote system, or gate mechanism. Please bring the necessary testing tools and have previous experience with solar-powered automatic gates. Please submit your genuine and reasonable offer, along with your experience and availability. If parts are required, please identify the fault and discuss the cost with me before replacing anything. Looking for someone reliable who can diagnose the problem properly rather than simply replacing components unnecessarily. Location: Warner 4500

Pre-existing automatic sliding gate in the property has a motor that is no longer functional and needs replacement. 240Vac power is available and functional. No electrical work required. Supply and install a new motor to drive the gate.

Need it fixed and change motor if needed.

The gate gets stuck part-way when opening or closing. I suspect something is wrong with one of the gears as it doesn’t appear to be an issue with the electronics. I can get it to open/close if I give it a hard push while pressing the remote.

We require an automatic gate opener for the existing double swing gate. Each side is 2m x 1.8. Electrical is in the ground per the pic

Looking for someone who can repair an automatic gate. The gate got damaged and isn’t fully closing.

Looking for someone to install a LockMaster EKD700M Dual Swing Gate Opener onto our existing double swing gates. The opener was purchased around 5 years ago but has never been installed, it has remained in storage since purchase. The job includes: Installing the gate opener onto the existing gates. Installing the control box and motors. Programming the remotes and testing the system. Letting me know if any additional brackets, posts or mounting hardware are required to suit the existing gates (happy to discuss additional material costs if needed). Please quote for labour only. Happy to provide photos of the gates if required.

My automatic gate derails after closing and does not open until I manually lift and put it back on track.

Automatic gate working intermittently need someone to take a look and repair

I need someone to install a "Slide 600 Gate Opener MGSK600" into my residential property. I will also require an electrician to disconnect the old unit and reconnect a new unit. Ideally this would be an authorised installer so that the warranty of 3 years applies

The pool gate needs a spring mechanism to close the gate.

Remove , supply and install a backyard timber gate , 1.8 mx 600cm.

Supply and Install Timber Gate on side access of house to backyard

Install New Timber Gate Post – Subiaco Looking for a handyman or carpenter to supply and install a new vertical timber gate stop against an exterior rendered brick/concrete wall. The old rotten timber has already been removed. Job includes: - Supply and cut new H3-treated timber to match original dimensions. - Secure timber to masonry wall using suitable anchors/fixings. - Existing masonry fixing holes are present but may require replacement anchors or new holes. - Ensure gate closes properly and latch aligns. - Prime, seal and paint timber to match existing colour. Photos attached showing the wall and existing fixings. Location: Subiaco, Perth Budget: $200 including labour and materials, negotiable. Please bring all necessary tools and materials.

I need to install a timber gate in my backyard, need it done by tomorrow

Diagonal beam and horizontal beam damaged by delivery truck. These need replacing, and the replacements need to match the existing. New timber will need to be properly undercoated, and then the entire gate including frame and posts will need repainting. New timber will likely need several coats to ensure it isn't obviously a repair.

Repair and reattach an existing timber gate. Bicton WA 6157, Australia I’m looking for someone to repair and reattach an existing timber gate. The gate and gate posts are already in place, but the existing hinges and latch need replacing. The job would involve: - Supply and install 2 suitable new heavy-duty gate hinges. - Reattach the existing gate securely to the existing gate posts. - Supply and install a new latch similar to the one shown in the attached photo — preferably a sturdy black powder-coated latch. - The existing gate may need 2 new timber slats/rails fitted to provide a solid fixing point for the new hinges. - Check that the gate is properly aligned, opens/closes smoothly and is securely supported. - Minor adjustment/repair to the existing timber as required. Gate and posts are already there — this is primarily a hinge, latch and reattachment job rather than a new gate installation. Please include labour and materials in your quote, and let me know if you need any further photos or information before quoting. Images sent previously

Hang a gate and cladd frame both sides in treated pine decking

Quote pleade: Need timber gate painted with weatherproof paint. Gate is roughly 3m x 2m.

I need a simple timber gate built and installed

3 timber gates are tired. 2 need the latch reattached. Bog holes. And stop the side gate scraping the ground so it can be opened from a wheelchair.

Handyman needed to fix & secure sagging timber gate, must have own tools.

We just put up a new fence and I just wanna put a side gate to the house just so I can lock it up. Have a look at the dimensions in the photos. I’m just looking for someone to get the materials and do the labour. I have a Bunnings trade card if that helps. It’s 1.7 -1.8 meters tall same as the fence . With some locking mechanising as well please

I need both of my back gate hinges replaced, ideally with corrosion-resistant hinges (galvanised or steel). The gate is a timber gate on a timber-and-flat-steel frame. Possible minor timber repair if rot is spotted - open to discussions.

Timber securing hinges to timber door needs replacing (as do the hinges). I have timber, hinges and screws just need install. You will need a few nails. Timber is hard wood.

For my mother- Repair timber gate and putty holes on wall and paint from painting that have been put up.

I need a small timber gate painted nicely. It will need to be painted with a primer then a few top coats It’s been lightly sanded. It needs some screw holes or gaps filled and it needs more sanding. I will provide paint, sandpaper, brushes, rollers

Looking for an experienced handyman, carpenter or fencing contractor to repair a side access gate at my home in Collaroy Plateau. The gate has been damaged and the timber has split around the hinge fixings. The gate frame may need repair/reinforcement, replacement timber sections, and hinges re-fixed. I’d like the repair assessed on-site and completed properly so it doesn’t happen again. Requirements: * Experience repairing timber gates and fences * Own tools * Able to assess whether repair or partial replacement is the best option * Supply any required fixings/hardware (I’ll reimburse materials) Photos attached.

Looking for a handyman or fencer to reinstall a timber gate with steel frame that was removed on side of our house for construction in the backyard. Hole for post is still there, gate still attached to post, latch still attached to externall wall of house. One missing panel that was damaged in the removal. Have purchased extra timber panels and timber rail just incase. Location is South MacLean 4280. Space is 2.8m wide. 1.8m tall.

Looking to get a basic timber gate built and installed on the side of our house. Approx width would be 1.7m. There was a metal fence there previously so it already has some fence posts. Slight incline also. Won’t need it painted, just need it installed

1. Install door closer (pictured) 2. Timber strips screwed into brick to aid function of timber gate 3. Drill. Rick for 4 screws to hang pictures on outside walk