Find a professional gate installation near you

Require the automatic gate rollers replaced. We have the new rollers available.

Replace motor on automatic sliding roller gate.

I need help connecting our new remote control keys to our automatic gate that is in our shared apartment block.

I need an Automatic Swing Gate mechanism & controller installed. I will supply the kit (info below). This is to replace the broken existing mechanism/controller from a different brand, which needs removing. There will likely require some drilling & fixing of mounts (hardware included - you will need tools) and setting up the gate controller/keys for open and close (instructions included). There is a power point at the gate, so no electrical qualification needed. I prefer if you have experience with installing Auto Gates and/or this type of system... please let me know. Kit information: Vantage 400 Single Swing Kit from Centsys https://www.fenceworld.com.au/shop/vantage-400-single-swing-low-voltage-23684?category=13

I need an experienced automatic gate repairer ASAP. My automatic gate won’t open or close and the manual mechanism (key) isn’t working.

Need a quote to fit up a complete automatic gate opener to my front gates I have the arms/ motors solar panel and battery pack etc all new Dig small trench across gate way and bolt everything up etc

Its stuck sometimes not closing

Need to pair a new remote to Automatic Gate

Several vertical bars are bent and need to be removed and replaced. The entire gate needs to be repainted.

1. Install external isolation switch (no external power, need to break out from internal GPO) - yet to buy materials as I wasn't sure if required 2. Install external GPO on fence post - have hardware 3. Replace 3x external lights to down lights with plug base outlet - have hardware 4. Replace sensor light and convert plug base outlet - have hardware

I need this automatic dual swing gate opener system installed in my existing garage timber doors. Purchased from Big W. https://www.bigw.com.au/product/automatic-electric-gate-opener-double-swing-remote-control-kit-800kg/p/9900145661

The double swing gate with Aleko opener • One leaf is noticeably faster than the other • The closing part is not done properly and completely closed Unsure if the problem is aging motor, hinges, uneven ground or whatever issues, wanna it be fixed and open & close properly

The gate is currently rubbing on the fence due to misalignment. May involve bit of concrete work as the gate may misalign due to block moving and there were two big trees until recent.

One side of front gate not returning to closed position. Motor is working but something must be wrong or disconnected with the return mechanism. I have had to disengage the lock/unlock grey lever to open and close that side of the gate.

Installation of an automatic sliding gate. Will need the gate built same as existing fence and electrical run back to box approx 8m for power for the gate. May need some additional concrete slab to support roller. Also open to ideas from a professional.

Front sliding gate currently has an old remote opener that runs extremely slow and often gets stuck. Looking to replace this with a new opener that can handle the double length gate. Installation may require preparation of ground/gate/tracks to ensure it runs smoothly and will last.

Hi, Job: Small concrete slab for automatic gate Location: Westmead, NSW Description: Looking for a concreter to pour a small concrete foundation for installing automatic driveway gates and gate motor. Area: Under 5 sqm Residential property Excavation required is already done - Just need to prepare concrete and pour with finishing Must be level and suitable for gate/motor install Timing: Ideally by this weekend (before 29th March 2026). Please message with availability and price. Thanks.

Driveway gates not working. Mate be control box issue

Hi, I’m looking for an experienced fencing contractor to supply and install the following at my property in Westmead: Scope of Work: - 1 x Automatic aluminium blade sliding gate – approx. 4 metres wide - 2 x Aluminium blade pedestrian gates – approx. 1.4 metres each - All gates to match in design (modern aluminium blade style - Surfmist Color) - Automation system for the main gate (motor, remote access, sensors, etc.) - Supply of all materials, installation, and setup - Please include details of the automation system brand and warranty - Site is in Westmead, NSW – happy to arrange inspection if needed Request: - Itemised quote (materials + labour) - Estimated timeframe for completion - Examples/photos of similar work (if available) Please feel free to reach out if you need more details or want to arrange a site visit. Thanks, Phani

Looking for someone to remove the old automatic gate system and install a new one. Gate controls need full replacement. Please quote for labour and parts. Location: Airport West, VIC 3042. Experienced gate technician required.

Unfixed palings on bottom of timber gate. Need to be nailed in. Gate latch is also loose and needs to be screwed in. An additional internal door handle to be reduced. Currently loose

Timber gates including any required posts and hardware. a) 1800mm x 800mm (approx) b) 1800mm x 1200mm (approx) Widths to be confirmed by successful tradie. Need to discuss location and what posts are needed. I tried to add photos but they failed to load. I can send photos.

I have 2 existing timber gates with a steel frame in Ballarat. I’m looking to install a gate handle or mechanical keypad lock. May require drilling into the frame and aligning latch. Keen for supply & install.

I have an existing timber fence going to a side patio. I am installing the patio roof. After this, I can’t use the existing gate since it is against the pillars. I need to permanently seal this door and make a new door for entry. I am also open to other options.

Looking for a handyman/carpenter for two jobs to keep our cat contained. Job 1 – Timber Gate (side passage) - Width: 1.3m, Height: 1.8m - Timber frame with timber palings - Self-closing hinges (must shut automatically) - Latch at the top - No gaps at the bottom - Fixed between brick wall and Colorbond garage wall Job 2 – Timber Paling Extension (other side of house) - Width: 1.37m, Height: 0.7m - Fixed on top of existing 1m brick wall to bring total height to 1.7m - Timber palings, no gaps - Cat containment purpose

A new set of back timber gates and 3 external cupboard doors measuring 2380 x 615 x 40mm. Plus replace a slat of timber in our front fence.

Washing line posts need reshoring and line needs to be restrung. Side timber gate requires securing to wall. Front timber gate requires planing as swells when it rains.

Looking for a carpenter/handyman to supply materials and complete a gate job at my property in Malvern. Scope of work: 1. New Gate (Main Job) * Cut opening in existing timber paling fence * Supply and install 2 new posts * Build and install timber gate * Include all hinges, latch and drop bolt * Match existing fence as best as practical * Doesn’t need to be high-end — just solid and functional 2. Fix Existing Side Gate Side gate currently not closing properly Needs adjustment Requirements: All materials supplied by you Must be sturdy and built to last Previous experience with similar work

Front timber gate has had movement and drags on concrete pathway Needs to be removed and adjusted

See pictures attached for your reference one side gate has fallen. Need timber post and bolting the door to timber post I believe

Timber decay causing the timber gate bracket to snap. I will need help replacing the timber jamb, gate bracket and reinstall timber gate.

I would like a side gate made and installed. Timber with latch. I have included a picture of another gate on the property and I would like this one to be the same

Looking for a handyman to tidy up a timber gate post that was poorly built. It’s structurally fine but the outer boards are uneven and patched. Job would involve: Removing some outer boards Re-cladding with straight timber Squaring up edges Filling/sanding joins Prepping ready for paint (or painting if possible) I have timber offcuts available that can be used. Located in Brunswick East. Flexible with timing but hoping to get it done soon as the house is being prepared for sale.

Timber gate in corner needs new post to attach gate with hinges. Collapsed 5 months new colour bond on the back boundary will be fixed by original contractor. Please see photos. 1st photo after the storm 2nd photo taken from inside garden, it was before the storm, in perfect condition

External gate frame water damaged and needs to be replaced. Material costs to be reimbursed seperate to fee

We have an old timber painted gate. The timber is rotting so I need a timber replica built and hinges and latch moved from old to new gate. Task would include buying materials, making the new gate and installing.

Remove one old double timber gate and replace. Remove one old single timber gate and replace. New gates to be made from timber. Build one small slatted fence, approx 3 metres long.

Large outdoor timber gate / door. Need to change direction from opening inwards to open outwards. Also to install a deadlock / deadlatch (supplied)

Need a timber gate for front entry to property prefer steel frame with timber slates to match existing fence

Fence Timber Gate has come off, need help to put same gate back.