42 Electricians in Coburg

Remove old outside light next to a door and replace with new - no ladder needed. Also, put new lamp holder, cable and plug into an old bottle lamp that had ancient wiring. Happy to buy the cable, plug and switched lamp holder if you advise what I need to get so that it is ready and waiting at our house.

Installation of NBN line into home (FTTC)

Remote controlled fan/light has stopped working due to receiver. Require electrician to source part and replace/install. Time flexible: ideally this week.

Update - now install only. 2x LED batten led lights with switches. and 1 x DGPO to stud Located in attic with good access and close to the switchboard. switchboard is contemporary. Timing flexible - can be done most days.

Fit a new electric oven. The existing oven does not work. The wiring is fine, It's a simple job will not take much time.

Looking for someone with electrical skills to set up electricity in a garden shed/hobby room. It used to have power many years ago but was cut. It will probably need to come from cabel from main house rather than underground. Based in Coburg. Price negotiable

Hi Ahmed, Does Thursday about 1pm suit? Cheers Bill

LED make-up mirror hard-wired and installed onto a wall. Refer photo for example. There is a power source on same wall. Specs: https://www.reece.com.au/product/vanities-mirrors-c621/mirrors-cabinets-c623/mirrors-c689/kado-aspect-800mm-round-led-mirror-9507917

Need a commercial oven wired in, an exhaust fan/canopy wired, air conditioner wired, a 15 amp switch for a coffee machine and a 10amp plug wired outside.

IXL four globe heat light to be installed & power for mirror light in bathroom renovation

We need someone to install as following: - two Urban 2 Ceiling Fan with E27 Light by Fanco – White 52″ with wall controls (excising electricity for light available) - two pendant ceiling lights in living and dining room area (with dimmer/controller switch) Please see photo as indicator for ceiling/access in all four rooms

Create a new light fitting to be connected to an existing light switch (replacing the double light switch for a triple light switch). Hang pendant lamp. You'll need to supply: -triple light switch -cabling from existing existing light switch to new socket created for pendant - tools to cut hole in cieling - ladder to get access to cieling which is above stairs

Lights stop working outside shop

LED make-up mirror hard-wired and installed onto a wall. Refer photo for example. There is a power source on same wall. Specs: https://www.reece.com.au/product/vanities-mirrors-c621/mirrors-cabinets-c623/mirrors-c689/kado-aspect-800mm-round-led-mirror-9507917

I need to replace the old electric oven with a new one. The size is 600mm(height) by 600mm (width) by 600 mm (depth).Please advise me the price to pick it up in Coburg Harvey Norman warehouse, dispose the old one and install the new one.

1. Fix two outdoor sensor lights 2. Replace covering of a power outlet which has a broken switch

mid century lamp requires full rewiring. It is a very old style that has a central post that feeds two bendy arms both with globes. The wiring is currently burnt out, and also the fixtures for the globes (the bits they screw in to?!) are broken.

Supply and Install: 2 x mains connected 600mm LEd batten lights with switch (eg https://www.beaconlighting.com.au/bayside-jedda-led-600mm-white-batten ) 1 x DGPO to bare stud. Both in attic space. Switchboard is contemporary. access is good via pull down stair. update- job to be completed before Saturday.

I purchased an electric toothbrush online and it came with a Euro plug instead of an Australian plug. I can just use a converter but I bought as a gift and wanted to see if I could fix it? Thanks Steph.

Need an internal pathway installed to run the internal cable from Utility Box (PCD) to NTD installation location