Find trusted local electricians near you

Air conditioning unit stopped working, switches on but no function after that. Old style unit looking to fix for a house sale rather than replace. Need job done asap. Thanks

I need a new electrical circuit installed for an induction cooktop and oven. Also need five PowerPoints installed in the kitchen. There is easy access above from the roof and also from underneath the floor on the ground level. There are existing PowerPoints close to where I need the new ones, they are just not quite in the right spot.

Replacing macerator toilet unit in granny flat. Current unit is running a cord from unit into a fixed 240v wall switch. Need wall switch changed to a 3 pin power point before plumber can install new macerator.

Task Description: Looking for a qualified, licensed electrician in st marys area to supply and install Clipsal MAX9 safety switches across all 6 sub-circuits and 1 solar main switch to comply with AS/NZS 3000 rules. Tasker to Supply & Install (7x Clipsal MAX9 items total): N.1 (Air Cond): 1x Clipsal MAX9 20A 30mA Slim Type A RCBO (MX9R3120) N.2 (Hot Water): 1x Clipsal MAX9 20A 30mA Slim Type A RCBO (MX9R3120) N.3 (Oven / Cooktop): 1x Clipsal MAX9 25A 30mA Slim Type A RCBO (MX9R3125) N.4 (Power): 1x Clipsal MAX9 20A 30mA Slim Type A RCBO (MX9R3120) N.5 (Power): 1x Clipsal MAX9 20A 30mA Slim Type A RCBO (MX9R3120) N.6 (Light): 1x Clipsal MAX9 16A 30mA Slim Type A RCBO (MX9R3116) N.7 (Solar Main Switch): 1x Clipsal MAX9 25A 1P MCB (MX9MC125) (Grid Supply Main Switch on far left remains as-is). Requirements: Must hold a valid NSW Electrical Contractor / Supervisor License. Perform RCD trip-time safety testing on all 6 new RCBOs. Issue a mandatory Certificate of Compliance for Electrical Work (CCEW) upon completion.

Electrical Installation required in Brand New Single story house (25m2) ————————- All material supplied (except ceiling fan studs), only need installation. ———————— x4 ceiling fans to install (electrical points already there, May need to install stud, not sure its there) ———————— X2 small chandelier (electrical points already there) ———————— X3 pendant light over kitchen island (electrical points already there) ———————— X3 sets of wall scone lights (each set have x2 lights to install left+Right) (x2 sets indoor and x1 set outdoor) ———————— x1 ceiling track Chanel light installation (electrical point already there) ———————— x1 TV wall mount (75 inch) need clean installation with all wires hidden (I already have NEW wall bracket purchased) ———————— X1 electric front door lock to install ———————— X1 dual electrical power point installation in one of the corner of house ————————

install WiFi relay control on two pool/spa heat pumps (8.7A and 17.5A, 240V). Parts on hand: Shelly Pro 2PM, 25A AC-3 contactor, RC snubber. Mount on existing DIN rail in switchboard, wire smaller unit direct through one relay channel with snubber fitted, larger unit through the contactor via the second channel. Existing isolators stay in place.

My hot water system is not working properly. Warm water is coming from all the taps.

Our microwave oven is causing the power to trip when used, which causes the circuit breaker to switch off. We need a licensed electrician to inspect it and determine what needs to be done.

Need new headlights installed

Wall switch does not press down to turn on

I have purchased a piece of equipment from China and need the wiring concerted to Aussie standards and safety check

I’ve got a garage studio where the power occasionally trips when high-power appliances like the kettle, washing machine or heater are being used. I believe the garage and some of the downstairs power points may be running on the same circuit. Could you please assess whether the load can be redistributed across the existing circuits, or whether it would be better to install a new dedicated circuit? I’m just looking for the most cost-effective way to prevent the power from tripping.

Looking for two existing power points in our living room to be converted from two to four outlets. Seeking a qualified electrician to provide new faceplates/materials and labour for combined fixed price.

Need a qualified sparkie to fit a Delta smart double touch switch. This will swap out a typical double switch for a toilet light and fan for a delta smart switch (bought from Bunnings. https://share.google/rS4iXqqqL0GGXaFe1 ) that will put the fan on a timer.

We’ve got 4 light switches that are stuck and/or pressed in. Want to get these fixed so they’re no longer stuck. Located in Bowen Hills

Looking for a qualified electrician to install a double power socket in both the kitchen and the laundry. Plastered walls. Single story with roof access.

I need my ev wall charger installed to power.

Needing someone to complete: 3x Ceiling Fan Installations - will be fitted to replace existing light. Fan is remote controlled. Will be installed to 3 bedrooms upstairs - gyprock ceiling. 2x Ceiling Downlight Replacements - will be fitted to replace existing light panel - concrete ceiling in living area. I’ve already purchased the ceiling fans and downlights. Happy to answer and questions you may have. Open to all quotes.

Need two existing light fittings changed to modern down lights

Looking for a licensed electrician to replace a broken Clipsal light fitting/batten holder. The existing fitting is shown in the photos, along with the replacement fitting. This should hopefully be a straightforward swap using the existing wiring, followed by testing to make sure everything is working safely. Job: * Remove existing broken light fitting * Install replacement fitting (provided) * Connect to existing wiring * Test and confirm light is working correctly * Replacement fitting is already available/pictured Timing: ASAP preferred. Available today/tomorrow if possible, otherwise Monday–Friday next week (24–28 August) works well. Please bring any tools/equipment required and be appropriately licensed for electrical work.