Find experienced local carpenters in Inner West Sydney

Carpenter to build concealed door Build and install a concealed door 2m wides 2.6 high with mirror and side architectural panels see inductive image I will pay for all materials including Mirrors you must organize them especially the hinges you Must have all required tools and be skilled in carpentry and joinery

Door panel has broken off my storage unit and needs to be refixed on

Fix & Align Kitchen Cabinet Door Location: HOMEBUSH (Flemington) Budget: $70 Date: Flexible The kitchen cabinet door is misaligned and catches on the left-hand side when closing. It requires a gentle push to close fully. Tasks: * Inspect the cabinet door, hinges and fittings. * Adjust and realign the cabinet door. * Ensure the door opens and closes smoothly without catching on the cabinet frame. Experience with cabinet door repairs preferred.

2 x caddy's and 1 x glass cabinet

Looking for an experienced carpenter or joiner to adjust a set of sliding doors and repair damaged base timber. Scope of work: - Relocate sliding doors from the external tracks to the internal tracks. - Adjust clearances as needed (planing timber edges, adjusting roller carriages, or shimming) so both doors slide freely and latch properly. - Cut out the rotted timber section under the external base (shown in photo) and install a clean replacement piece of exterior-grade treated timber. - Seal joins with exterior gap sealant / Sikaflex to ensure weatherproofing. Details & terms: - Please bring your own tools (planer, saw/multi-tool, chisels, drill, level). - Listed budget is for labour. Replacement timber and consumables can be reimbursed directly with receipts, or included in your offer if specified. Location: Leichhardt (easy site access and street parking available).

Preparing house for sale and looking for an experienced handyman or carpenter or landscaper to repair and refresh the backyard fence and decking Timber fence – approx. 32 linear metres total •Repair/reinforce approximately 10 fence posts/sections as required •Re-nail/resecure loose fence palings •Replace any minor damaged fixings •Clean/prep fence •Scrape/sand rough or loose areas as necessary for painting •Apply 2 coats exterior fence paint •Fence will be painted dark charcoal Timber back deck – approx. 5 m × 4 m (20 m²) in pretty good condition. •Repair/resecure minor loose board (one area only) •Clean and prepare •Sand appropriately for refinishing •Apply 2 coats quality exterior decking stain/oil Please quote for labour. Materials can be supplied by me or purchased by Tasker and reimbursed by agreement. Please bring your own tools and sanding/painting equipment. When making an offer please let me know: 1.Your experience repairing timber fences/sanding and staining decks 2.Whether you recommend spraying or brushing/rolling the fence 3.Whether your quote includes all labour for two coats Priority is a tidy, durable, professional finish for presenting the property for sale, rather than a complete rebuild.

Make a Cabinet in both room

need two holes cut in existing cabinetry for the pipes and electrical cords for washing machine and dryer - need a hole saw and jigsaw

I have three carpentry tasks I need completed. 1. Complete the corner join of VJ panels in stair well - I have the materials I need someone to join the corner properly and caulk the corner 2. Fix the reveal of an outside door and remove the gap at the top. This will involve removing the packers and adding wood to compensate on the hinge side. 3. Supply, cope and stick about 1.5m of skirting (to be supplied by you from swaddlings - I can provide the example piece)

Seeking all inclusive booking. Scope: Looking for a carpenter/handyman to construct a basic residential ramp and decking walkway along the side of my house. Details: Total length: ~13m (ramp section + level deck) Width: ~900mm Height: ~450mm (variable) Ramp to rise from ground level up to existing door height (final rise to be confirmed onsite) Continue as level decking along side of house Install simple, durable timber subframe + footings on concrete and existing laid brick. No digging required. Finish with timber decking boards (not merbau) Tie neatly into existing door threshold Ensure proper drainage fall and weatherproofing Site conditions: Narrow side access (approx. current width shown in photos) Fence boundary on one side, house wall on the other, both may be used for additional stabilisation. Build requirements: Solid, level, and straight finish Outdoor-rated materials (treated timber frame and decking boards) Suitable for regular foot traffic Slip-resistant surface additional option Looking for: All inclusive booking. Supply + install OR labour-only (please specify) Licensed/experienced carpenter/handyman preferred Must be familiar with Australian standards for ramps

Assemble 2x Metod Maximera kitchen cabinets. Each cabinet has two drawers, a medium and large. The cabinets must be fixed together. Fixing to the wall is not required, just cabinet assembly. The image below is close to the end result. Parts in red will not be included. Extra drawer added in blue. Dims each cabinet: 40W x 37D x 80H Task must be done between 12-5pm. Visitor parking available or street parking. Own tools required.

Our Merbau timber deck needs sanding, staining and sealing for the upcoming summer - we have previously had it sanded back slightly but it is in real need of redoing. Prefer if you arrange for the materials but I can arrange for the sealant / stain to be provided - please clarify on any quote if it is with materials included or not!

Supply and install approximately 35 cabinet door hinges in kitchen

We recently had blinds removed from around these timber doors/windows, and the top section has been left looking unfinished. I’m not exactly sure what needs to be done, but I’d like the top of the doors/windows to look the same as the timber sides, so it looks like there is one continuous, finished timber border all the way around. This may mean a new architrave to match the left and righthand sides Looking for someone experienced with carpentry/joinery who can look at the photos, advise on the best way to do this, and complete the work. Ideally the new timber/finish would match the existing frame as closely as possible. Please include your proposed approach and approximate materials cost in your offer. It would need to be done some time this Sunday or Monday. Thanks!

Looking for someone experienced to oil/stain our new timber fence in Drummoyne. Fence is approximately 8.6m long × 2.1m high (18m²) * I will supply the timber oil * You supply brushes/rollers and all other equipment * Protect surrounding artificial grass, paving, walls and garden from drips/splashes * Leave the area clean and tidy afterwards Only the one visible side of the fence shown in the photo needs to be done. Looking for someone with experience.

I have a wall cupboard that was damaged while being moved. I have removed a 600 x 400 x 2100 cupboard section and have a ready made replacement for that section. All 10 doors need to be drilled onto the unit. I have photographed both the wall unit and the replacement section. The unit may be best fixed while lying on floor allowing you to remove the old cupboard side without the whole unit falling apart (Lie it down?). This is not a hard job, it just requires somebody who knows how to use tools. If you need help there are two of us here to help lift or move or hold it while drilling. My partner and I are here to help Sunday 6th after 3pm or Monday 7th afternoon or Tuesday morning 7 - 9.30 am or 11.30 a m - 1.30 pm the following saturday 11th. PHOTOS: 1 Entire BESTA unit 2 The side which requires 2 parts being removed 3 same 4 same 5 The unit that will replace broken part (same BESTA product) Doors to be changed

My pantry cupboard door has come off the hinge. I’ve tried replacing it myself, but it broke again. Seeking someone with cabinet repair / building experience.

Hi, I require x2 cabinet doors to be made with pre drilled hinge holes. Dimension: 730 x 393 x 18mm Colour: curl birch natural finish. Thanks

Big cabinet door needs to be fixed. The left door has come off completely. No idea how it has to be fixed? Soldered?