Scratch on kitchen cabinetry needs repair. Not just a surface mark. Scratch is probably 1mm deep and 200mm long on white gloss panel - Due date: Flexible

Small narrow shed 3 metres long x 2 metres high x .78 on concrete at side of house - Due date: Flexible

Adjust kitchen cabinetry shelving to accomodate new Rangehood to fit - Due date: Before, 22 October 2022

Hi, We need to pour concrete (steel reinforced, 300mm deep, minimum 20MPa strength) around the pool to install glass panels. We also need to concrete all the area on the back of the house. I have attached a few pictures for your reference. Thanks - Due date: Flexible

Hi, I’m looking for a builder that would know how to make a bbq bench or could suggest/source what materials to use for it as well as install it. We did not want to spend too much on it, but please make an offer and we can negotiate budget based on materials and work hours. Its a simple job, we just want to make the space look more tidy and clean it doesn’t have to be too fancy. - Due date: Flexible

Adjust kitchen cabinetry shelving to accomodate new Rangehood to fit - Due date: Before Sunday, 9 October 2022

Clean with my guerney Sand Stain - Due date: Flexible

existing concrete floor maybe (?) no stain guard, and a food spill has left a white/bleached stain on the floor. needs concrete hardner re-applied and polished. approx 1.5m long and maximum 30cm wide in the widest part. - Due date: Flexible

Looking for a handyman or painter to paint over about a dozen water stains on the ceiling in the kitchen, lounge/living rooms and bedrooms. The ceiling is of a standard height and colour is standard ceiling white. Single story small to medium sized 4 bed house. Will consider quotes to paint over the stains only or repaint the entire ceiling of these room (approximate size is 106 sqm). It's an investment property. The finish doesn't need to be perfect but needs to be acceptable. - Due date: Flexible

Hi I’m after a qualified plasterer to repair crack where 2 plaster boards join , one side feels like there is a baton behind it but other side doesn’t , it’s about 600mm long from bottom of window to skirting board , I can sand it once it’s been taped on join and bogged up - Due date: Flexible

3m in total of cornice needs to be put up and set in our kitchen. 1.5m has already been measured and cut, just needs to be set. Needs to be done before the weekend in Elanora. We will supply cornice and setting paste.

small wooden cabinet 110 x 65 x 50cm needs sanding and restaining/varnish - Due date: Flexible

Our current plasterer has hurt himself and is unable to finish off our kitchen plastering and some stuff other areas. We need the kitchen finished this week as kitchen goes in next week

we need a 4.5m x 3m garden shed installed on a slight slope, needs levelling and slab laid - Due date: Flexible

We need a cabinet removed and replaced with a bench seat with storage underneath. A cupboard lock repaired. 7 draws replaced and bench top fixed or replaced. Cooker fitted in cabinet. This is in a New 27ft motorhome . We have a full size door and it has never been used. - Due date: Flexible

Exiting rental property and needing to replace laminate on kitchen bench. Needs to colour match > see photos

Complete deck drawings for deck already built to be submitted for council approval

Hi, I have a 1860 long x 850 deep brand new Stratco shed I need installed in Elanora asap. New slab is ready for install. Link below to shed https://www.stratco.com.au/au/sheds--garages/garden-sheds/handi-mate-garden-sheds/handi-mate-sliding-door/ Cheers Brad

Looking for handyman to install: - full pj panelling on 2 walls - half height pj panelling on 2 walls -picture shelf across 2 walls Someone with experience in this type of work preferred. Materials will be provided and panels will be cut to length/width.

I have a Toyota coaster bus. It’s got a king single bed plus frame. I’m wanting to make it a double. I’m needing the frame bars moved accordingly. They are steel bolted into bus. Then I need the ply screwed down on top of frame to complete the double bed. I have the ply. You need tools and a circular saw to cut ply to fit.