Find an experienced handyman in Paddington QLD

Plasterboard dint repair - remove existing, resheet damaged area, plaster and prep for painting

I have 2 Freedom 2.5- 3 seater sofas that look good but are uncomfortable - they sink in the middle when we sit on them. They have straps (webbing?) underneath that seems quite tight but are obviously not doing the job. We need them to be restored to make them more comfortable.

Need tow 8mm holes drilled to be 10mm they’re on two headlight brackets for a motorbike.

I need a new remote controlled ceiling fan installed in my living room. The room currently doesn’t have a fan, so this is a new install. Needs to be done by a qualified electrician. Roof access from room next door. Thanks!

Looking for a professional to repair a MagnaLatch gate latch system. The bottom part of the latch has come off and may need reattachment or replacement. The job involves assessing the damage and either fixing the current latch or replacing it with a new one to ensure the gate operates smoothly and securely.

Install trim around door Install trim around window Replace a few external wall boards Replace facia on deck Strip window hoods for painting

Hang wall cabinet, TV, whiteboard, screw door back onto frame and put door lock back on, install ceiling mounted curtain rails

Install the door closer on the door

Need to hang barn door on brick wall. Already have slider set for door.

Hang this barn door on the brick wall behind. We already have the slider kit. https://www.ebay.com.au/itm/395403985754

This is one of our clients who has an Electrolux double door fridge where the left side handle has broken off. The fridge is a discontinued item and nowhere is Australia or NZ has the part required to fix it. Would like a handyman to go out to see if it is repairable and if so if it can be repaired on the day?

Single seat sofa damage to wooden floor boards. Around 2x2m area. Need to mend before end of lease on the 26th of September, landlord is aware of damages and is our responsibility to fix. Flexible with time and date, can be anytime before the end of lease.

Need stripped screw extracted and replaced with new one. Needs to be done today after 4pm please. Is on a motorbike fairing

Remove damaged lockbox and replace with new one (supplied). Would estimate 15 mins. to complete.

Install Perma Child Safety Retractable Gate Own tools required. Subway tile & plaster board. Instructions for install: https://m.youtube.com/watch?v=4MH6utoW9Sk&feature=youtu.be

I need a safe attaching to a cupboard floor. Total of 4 bolts that go from safe floor into wooden shelve below.

Some minor set up and decoration for my shop: assembly, lights, Ring camera installation and decoration.

I have two large paintings to hang on a wall. I live in an old Queenslander and it’s a rental so need to ensure the job is done carefully so as not to cause any damage Both paintings and hung with two hooks on the back

Remove two metal hoods and install two new metal window hoods from Woodworkers. It's a one piece of metal hood that includes the flashing which needs to be placed under weatherboard walls and then screwed in with the right accessories to ensure longevity. Size: 95cm width Please note that you'll need your bring any necessary tools and joining accessories (screws and etc) as the hoods are being delivered without any accessories. - Please only quote if you have %100 confidence. - Access is easy, ground level. Woodworks generic explanation for install- Colorbond hoods can only be connected by pop rivet joints Metal hoods should clear the external jambs of joinery by approximately 30mm and are usually simply screwed directly to the chamferboards with dome head screws & nylon washers to ensure electrolytic compatibility with the hood metal. Remember water cannot flow over zincalume onto galvanised fixings. Because metal hoods are so light they can easily be installed by two people in a fully assembled state. The metal hood needs to be positioned to avoid interference with the window opening (especially with casements) and ensure pedestrian traffic cannot collide with the hood. Ensuring the hood and window are parallel, the top flange of the hood is usually slipped under the chamferboard or weatherboard overlap and the sides are screwed down with to 4 screws each side. 100) AA •

Will need to provide hardware suitable for plasterboard walls. Must have experience hanging art.