Find an experienced handyman in Blackburn South

Requiring for a shower screen to be removed by Monday 12 Oct and a new screen to be fitted on or after 17th Oct. Would also like for shower screen replacement options and recommendations.

Change two ceiling fans. Please see photos of old and new fans.

Has a hole behind kitchen tap needs to be fixed

The kitchen door hinge broke need to be replaced at my rental property. Is this something that you can do? Also how much do you charge? Also do you provide tax invoice?

See photos. Remove existing door frame, jambs and install new door frame, door and electronic lock. Take away rubbish. I will supply the door, frame, jambs.

I have a metal garden shed door that has come off its hinges and needs to be repaired and rehung. The hinges are still attached to the shed frame, however the rivets/fasteners attaching the hinges to the door have failed. Photos show the current condition. Looking for someone experienced with metal sheds/general handyman work to: * Remove/drill out the remaining broken rivets as required * Reattach the existing hinges to the door * Replace/reinforce fasteners where necessary * Rehang and align the door * Make sure the door opens, closes and latches correctly The door and hinges appear to be in good condition, so I believe this should be a straightforward repair rather than replacement. Please bring the required drill, rivet gun and appropriate rivets/fasteners. Budget: $150 including standard fixings/materials.

Looking to close up garden shed window. Supply install sheet metal on both sides (and appropriate screws/silicone) to block out window.

I need supply and installation of 2 custom frameless shower screens. Ensuite - approx 900mmx900mm corner frameless . Height 2100mm. 10mm toughened safety glass. Main bathroom - approx 1250mm wide space, will need 1 fixed panel and one door. Again frameless, height 2100mm, 10mm toughened safety glass. Will need on site measure up. To be installed onto tiled floor, all silicone caulking around to be completed.

Install a ryobi hydraulic door closer on office bathroom door

Please refer photos. Scope of works: 1) Existing ducted heating system has been removed. Cover/board up 4 ducted heating holes in bedrooms so that carpet/underlay can be laid straight 2) level sub-floor gaps between kitchen/living and kitchen/pantry so that timber flooring can be laid straight 3) cover/board up hole in pantry (as cabinetry will go on top) 4) front porch projection (gaps need to be sealed /patched, raise the support slightly so it doesn't look dropped compared to facade) 5) External weatherboard metal panel has 2 holes that needs covering 6) underneath front door and to the right of entrance (new metal weatherboard cover required to make it look integrated) Doors 7) new doors supply/install (Laundry, Master Ensuite, Pantry) 8) adjust sliding door in bed 2 so it slides properly (think it needs tracks) 9) bed 2 door, move door handle and catchment (currently it sits higher) 10) linen door install (we will supply door) Thanks

Can you please install this door back to the frame? Thanks

I have a Karcher K2 Power Control pressure washer that switches on but doesn’t build pressure and the water comes out as if from the hose. I’ve tried to diagnose the issue myself, there’s no leaks anywhere, and no cracks or broken fittings or split O-Rings. Am thinking it may be an internal pump/valve issue and am wondering if anyone might be able to help or advise?

Repair/replace damaged plaster

Fix the following Mirror on a wall in stairs. https://koalaliving.com.au/Buchannan-Rectangle-Mirror---Black Please note you will need flexible ladder to reach some areas.

need someone replace old benchtop(steal) with ikea benchtop(timber) and install sink for me

Hi, I'm after a handyman or carpenter for a small but slightly fiddly repair on an older timber door. The problem: the latch goes into the strike hole but won't hold — when you push the door it pops back open, so it won't stay locked/shut. What I've found: - The metal strike plate on the door frame is old and rusted. - The timber behind it (the pocket the latch drops into) is chewed out / damaged, so the latch has nothing solid to catch on. - One of the strike plate screws is stripped and seized — it won't come out. What I need done: - Remove the old strike plate, including the stuck/stripped screw. - Repair/rebuild the damaged timber in the frame so it's solid again. - Refit the strike plate (or fit a new matching one) and adjust so the latch catches and the door locks properly. It's a small job — roughly 30–60 minutes plus a few dollars of materials. Please bring your own tools; a replacement strike plate and screws may be needed (happy to discuss). I'll attach photos.

Install wall floating shelves with brackets.Material will be provided

Need new toilet seat fitted

Installing screenline privacy screens to existing timber fence. Approx 5-6m wide.

There's a hole on the wall and I need it fix thank you