Find an experienced handyman in Frankston

Security screen door has come off at the hinge, needs to be reinstalled

My old tv and fridge that have been replaced will need to be removed

Registered and licensed builder required for installation of grab rails and minor home mods for aged and disability clients.

I need 15 cupboard doors put on - they will need the hinges screwed and all level please

I’ve just bought a 2021 MG ZS I’m not a fan off the unpainted black and satin chrome trim pieces on the lower front and rear bumpers, the lower door trims and the wheel arches so I would like to get the painted the colour to the body which is white I would also like to paint the front and rear logos and the roof rails black too

Need 6 meters of cornice to be done

Need 6 meters of corners put up.

Just want a rectangle large enough for a medium size car to park on top of, so that anyone exiting the car through any door will not have to touch their shoes to the grass/mud.

The wet weather conditions over many years have rusted the base of the metal frame of my shed, as well as the bottom of the wall sheets. My plan is to have someone give me a hand securing some metal brackets between the concrete slab and the metal sheeting using dynabolts and fasteners. This will prevent the shed from rustling in the wind until I can get it replaced. Any questions sing out. I can supply the metal brackets as shown in the photo, I don’t have dynabolts or fasteners as I’m not certain as to the correct ones. The shed wall is 4m long with 3m affected by rust and swaying. Probably best to go all the way along.

1. We need two reinforced concrete base plates (500 in diameter and 800mm deep dug by hand) with a hinge plate attached. Wait for the concrete to cure and attach the pole. 2. We also need 3 holes dug for 3 posts 600mm deep to concrete in a sign. Job to be completed near the end of September. We have 3 sites this needs to be completed at (at a later date), the first being in Frankston. We need insurance certificate, workcover certificate and business details asap. Someone will be onsite to assist.

Looking for a Tradie/Handyman Job needs to be done on 21/08 (This Wednesday, morning preferred) Located in Frankston 3199 1. Cut Slatwall Panels to size, including aluminium inserts (3 Panels) 2. Mount Panels to wall

Remove 2m wall from floor to ceiling (plaster, any timber and small amount of cornice). Make sure it's ready for plaster. Cut off small corner of kitchen bench.

I need this sign removed from the second story of my old site. It's a simple led sign. Only the letters need to be removed

Floorboard is very sticky and moved down when stepped on. Looking for an experienced floorer to fix it. Only 1 edge floorboard needs to be fixed. Possibly just missing nail down

-3 laundry cabinets - already built (not flat packed) but need to be hung up on the wall - 1 laundry trough cabinet: Need to cut hole in the back to allow for plumbing. To be fixed to wall - onto ceramic tile - 2 side pieces to be fixed to the wall - onto ceramic tile - 1 laundry bench attached on top - stone. Tap and sink hole pre- cut *Attached is a picture of how it looks when it’s finished. *Quite heavy cabinets ~10kg each *Heavy long laundry top - stone Not needed: - no plumbing - no installation of laundry sink - no fitting off of taps - no tiling - no painting

1) Plaster wall behind removed gas heater 2) Repair small hole in wall 3) Repair small area where socket removed 4) Repair plaster under carport *Price TBA depending on work required

Large bathroom mirror has come loose from some of its fittings securing the mirror. The screw holes in the plaster need filling to secure mirror again properly. Need done asap before mirror falls.

Two corner shelves to be mounted on the wall in a nursery.

*Hang one mirror in powder room with plaster screws provided *hang one mirror on wall using double sided tape (you need to provide) it was hung using 3m tape Velcro strips but it fell off *hang 5 lightweight pictures into plaster using 3m hooks or nails (I have these)

INSTALL a brand new blockout blind on sliding door , just need an electric drill to finish the job