Find an experienced handyman in Langwarrin

I need someone to help install new front door and new jam, tile a splash back in kitchen and laundry, help install bath and vanities.

Looking for someone experienced to assemble and install a brand-new Instahut 4.5m x 3m motorised retractable awning in my backyard. Job details: • Assemble the awning as per manufacturer instructions. • Install above the existing sliding doors onto suitable structural supports. • Its a timber joist rather than conventional brick/blockwork • Install mounting brackets and securely mount the awning. • Adjust the angle and test the motor and remote. The awning is already purchased and on-site. Installation instructions and YouTube assembly video are available. I am happy to assist with lifting and positioning, as the awning is quite heavy.(only on sats) The area is easily accessible on grass. I have a platform ladder. Important: Must have experience installing retractable awnings https://www.bunnings.com.au/instahut-retractable-folding-arm-awning-motorised-sunshade-4-5mx3m-grey_p1198270

Electrician required to Install new ceiling fan where old Bayonet light fitting is. Offers please

I need an outdoor electric blind installed from masonry on one side to a steel post on the other. Can organise own electrician if required.

Need 7 door handles to be installed. door handles provided.

Cord to roll blind up and down is broken and needs replacement.

Patch/rebuild the missing plaster and skirting board on the ceiling.

need a handyman for 1 to 2 days worth of work, putting beds together and picture frames, tables for a 4 bedroom place, looking for hourly rate

Bathroom handrail was pulled out wall, repair wall and reinstall handrail - please review the photos to determine if the handrail can be reinstalled. If not please advise before quoting!

Supply and install two sliding wardroab doors

Door chipping in real estate property- minor. Some paint available for touch up.

Install external vent for clothes dryer — brick wall core drill required Need a handyman to install an external dryer vent. All materials supplied — just need someone with the right tools and experience. The job: - Core drill a 107mm hole through a brick veneer wall (plasterboard inside, single brick skin outside) at a slight downward angle toward the exterior (2–3° below horizontal) — required by the manufacturer to prevent condensation draining back into the dryer. Drill zone to avoid studs, noggins and any cavity cables — check before drilling - Fit the supplied Deflecto DK4W vent kit (wall cap, aluminium sleeve, connect flex duct to dryer rear exhaust) - Install a 100mm inline backdraft damper in the duct run - Wrap sleeve with foam insulation tape - Silicone seal exterior flange and interior collar - Fill any gap around sleeve with low-expansion foam Setup: Dryer backs directly onto external wall — straight rear vent, zero bends, very short duct run (~300mm). All materials provided. Please only quote if you have an SDS rotary hammer with 107mm masonry core drill bit — a standard drill won't get through brick cleanly.

Need to get this shed erected and anchored on a concrete slab. The slab is ready to go. I ordered anchors and flashings with the shed so fingers crossed they are in the boxes from easy shed

Install double blind on bathroom windown

Remove 1 x 55" and Install 1 x 55" screen on the wall in a café and install some software on the screen this week. Would suit an experienced AV installer or IT tech. The tasks will include: - Pick up the mount from Bunnings Frankston (it will be ordered under Click and Collect). - Check vertical and horizontal positioning with the store manager - Install screen section of mount on screen. - Calculate wall section of mount positioning - Install wall section of mount, ensuring to hit a stud or into solid timber. - Connect Power and LAN (if applicable) Cables - Hang the screen on a wall mount, ensuring the cables are not in the way. - Turn on screen. - Follow the on-screen instructions, skipping any step that is not listed below: - Make sure the internet is connected. Connect to Wi-Fi if Ethernet is not connected. - enter security code "000000" and confirm - Check date and time are correct for the time zone. - Select Custom App and enter HTTPS://fus.app/tizen - Once set up is complete push the home button and select The "Custom App" Fusion will install and should start automatically. - "Make sure Fusion Signage is online and showing a code. If no code is showing, check the following: - Is the screen online? - Is the time zone correct?" - Take photos of codes, noting the location of the screen and store name. - Send info to Benny to register. - Set Screen On/Off Timer: - Push the home button and select ""On/Off timer"" - Set the one timer to 1 hour before opening time and set the source to custom app. - Set the off timer to 1 hour after closing time. - Ensure all cables are out of sight. - Benny Should have uploaded content before you leave. - Completed Installation Photos sent to Benny

Minor rendering patch on a garage wall- see photo attached.

Render my fence panels Installed foam panels to fence Roughly 113sqm Finishing it off tomorrow and getting cut off clean tops to fence height

I can supply some cement sheeting just if someone could install it to my fencing approximately 50m worth the sheets all come in 1.2m lengths

I have a few indoor blinds to fit. And one that needs reinstalling as it keeps falling down.

We would like to install a doggy door into this window pictured. We would need a large door.