Find a professional gate installation near you

My automatic gate derails after closing and does not open until I manually lift and put it back on track.

Automatic gate working intermittently need someone to take a look and repair

I need someone to install a "Slide 600 Gate Opener MGSK600" into my residential property. I will also require an electrician to disconnect the old unit and reconnect a new unit. Ideally this would be an authorised installer so that the warranty of 3 years applies

Manual gate currently in place. Need it to be automatic so I can open and close existing gate with a remote control. It needs to lock in correctly and safety is of most importance

The pool gate needs a spring mechanism to close the gate.

Need to fit striker on pestering gate and intercom and complete automatic driveway gate

Install a TMT 400LLS Automatic Gate Opener to farm gate in Laguna. https://bmgi.com.au/images/tmt-wiring/TMT-Manual-small.pdf Recommends 3 hours installation time

Automatic Gate works great, Need closing gap adjustment. Please refer to photo. Experienced trade person only welcomed to offer.

We require a sliding automatic gate to be installed at our front fence line. There is an existing fence made of tee-tree on the fence line. The height of the gate would need to be at least 1.5m high and 2.5m in length.

Looking for an experienced fencer/gate installer to supply and install fencing and a motorised driveway gate at a residential property in Braybrook VIC (13 McLennan Street). Please see attached marked-up aerial photo showing approximate fence lengths and gate locations with colour coding as follows: • Green = Existing damaged fence to be removed and replaced (~26.9 m) • Red = New fence sections to be installed (~30 m total) • Blue = Existing front fence (~8.3 m) with possible 1 m height extension • Cyan = New automatic motorised driveway gate (~4.1 m opening) • Yellow = Existing side walkway gate to be replaced (~2 m) Scope of works: • Remove and replace existing damaged boundary fence approximately 26.9 metres long • Install new fence sections approximately 30 metres total length around driveway/side areas • Existing front fence approximately 8.3 metres long — preferably extend fence height by approximately 1 metre if practical/cost effective • Replace existing side walkway gate approximately 2 metres wide • Supply and install automatic motorised driveway gate approximately 4.1 metres wide for vehicle access • Gate must include remote control operation and safety sensor to prevent closing onto vehicles/objects Looking for: • Cheapest practical and reliable solution possible • Durable and weather resistant materials • Open to Colorbond, timber, sliding gate, or swing gate options depending on price/value • Open to solar or powered gate motor systems depending on overall cost effectiveness Please provide: • Approximate total cost including materials and labour • Recommended cheapest option • Estimated timeframe • Whether rubbish removal/disposal is included • Previous similar work/photos if available Location: Braybrook VIC

Gate opens but does not stop at the end, possible issue with limit switch. It then goes in a loop and doesn’t stop until button pressed. Only moves one way, not two ways.

Lock for automatic door has got the loosen key .

Complete installation of automatic kenner gate opener including power box installation

I bought a new house and have a manual steel gate that opens up to the drive way. I would like to use what’s possible to automate the opening and closing.

A double swing gate for an 4.1 x 1.76 m opening. Foldable gate is better to avoid using height-rising hinge. Need alumnimum alloy gate

The mounting bracket for my automatic gate opener has pulled out of the timber rail. I need a handyman to securely re-attach it so it can handle the tension of the motor. The job involves: • Reinforcing the mount: The original holes are stripped and show some rust staining. You will likely need to use larger timber structural screws or, ideally, bolt through the rail with a backing plate for maximum strength. • Re-aligning the arm: Ensuring the gate closer (piston) is level and functions smoothly without straining the motor. • Weatherproofing: Applying a bit of wood filler or sealant to the old holes to prevent further rot/rust. Details: • Material: Painted timber fence rail. • Equipment: Please bring a drill, heavy-duty timber fasteners (Coach screws or through-bolts), and basic wood repair tools. • Timing: Flexible, but looking to get it fixed within the next few days. Advice for the Fix • Don't just use bigger screws: Since those holes look a bit "blown out," simply putting a larger screw in might only work for a few weeks. • The "Through-Bolt" Method: Ask the Tasker if they can use "cup head bolts" that go all the way through the timber to the other side with a large washer and nut. This is the only way to ensure an automatic closer doesn't rip out again.

Automate gate or replace if needed. Currently not automated.

Require the automatic gate rollers replaced. We have the new rollers available.

Replace motor on automatic sliding roller gate.

Looking for someone to remove the old automatic gate system and install a new one. Gate controls need full replacement. Please quote for labour and parts. Location: Airport West, VIC 3042. Experienced gate technician required.

My timber gate has broken the timber post it was hinged to. The existing post needs to be removed, a new treated pine post installed in concrete, and the gate rehung with the existing hinges if possible. The gate should be aligned so it opens and closes properly.

We need a gate installed to fit within a 1300 gap. Gate can be any width 850-1000 the rest of the space can be small fence or post. Included are pics of the space (betwee shed and house) AND pics of an existing gate on the property, style we want to match to. Fixing method, open to suggestions, but needs to be secure. Materials - we are happy to pay for, please advise what is needed

Looking for an experienced handyman or fencing contractor to repair a timber front fence in Surrey Hills. Work required: Replace one broken gate hinge. Reattach the fence panel to the timber post (panel has separated from the post). Repair the cracked bottom timber rail of the fence panel, or replace it if it cannot be repaired. Please see the attached photos for the condition. I've also included a close-up photo of the cracked bottom rail to show its size and condition. I would like the fence and gate restored so they are secure and functioning properly. Please quote for labour only. If replacement materials are required (for example, if the bottom rail cannot be repaired), please discuss this with me first before proceeding. Material costs can be charged separately if agreed.

I need a basic timber gate installed in the corner of my back fence. I need it to be lockable

Timber gate on timber fence - the post has rotted at the base and no longer stands straight so the gate won't open/close properly. Need the post replaced and the gate to work.

Looking for an experienced handyman, carpenter or fencing contractor to repair a side access gate at my home in Collaroy Plateau. The gate has been damaged and the timber has split around the hinge fixings. The gate frame may need repair/reinforcement, replacement timber sections, and hinges re-fixed. I’d like the repair assessed on-site and completed properly so it doesn’t happen again. Requirements: * Experience repairing timber gates and fences * Own tools * Able to assess whether repair or partial replacement is the best option * Supply any required fixings/hardware (I’ll reimburse materials) Photos attached.

Looking for someone to replace our existing driveway gates and side pedestrian gate with a more modern slat-style design similar to the reference photo attached. Third picture is our current gates and want it like the second/first (AI) Scope: • Remove existing gates. • Supply and install new manual gates. • Driveway double gates plus matching side gate. Please send offer including materials. Happy to do it as cheaply as possible. Measurements are: Width of carport 2830 Each gate is 1350w x 1500h Side gate 1500 high x 900 wide

Timber gate has come off the post, just need it reattached please.

I need an experienced fencing contractor or handyman to repair my side timber gate in Toowoomba. Please note that some of the attached photos were taken before the gate fully collapsed, so its current condition is worse than shown in some images. I am looking for a proper long-term repair, not a temporary fix. The job includes inspecting the gate, frame and posts, rehanging and realigning the gate, and replacing all worn or damaged hardware with new heavy-duty components, including hinges, latches, catches and any other fittings required. I would like a heavy-duty drop bolt (slide-down ground bolt) installed to secure the gate when closed, as well as an additional heavy-duty sliding bolt or locking bolt fitted around the middle of the gate so it can be securely locked and supported when required. Any additional support hardware needed to prevent future sagging or failure should also be installed. I would also like a suitable hold-open mechanism fitted so the gate can be secured in the open position and not swing shut in windy conditions. Please inspect the existing posts and advise whether any post movement may have contributed to the failure. I am looking for someone experienced in gate and fencing repairs who can provide a strong, reliable repair that will last, as I intend to replace the entire fence at a later date. Please quote including labour and materials and provide details of your experience with similar gate repairs.

Need a timber gate that matches our new fence to be installed here. We want it so you can only open from the side path not the front outside. Needs to match the height of the fence basically with no gaps underneath as we have a dog. All materials required to be supplied by you.

The bottom rail of my side gate has rotted and needs to be replaced and some pailings need to be put back on

Timber gate needs hinges adjusted to allow it to close flush.

Detach large metal gate. Remove cemented in timber gate post. Replace with metal post. Reattach gate. It already has new hinges to be re-used.

Looking for a handyman or fencer to reinstall a timber gate with steel frame that was removed on side of our house for construction in the backyard. Hole for post is still there, gate still attached to post, latch still attached to externall wall of house. One missing panel that was damaged in the removal. Have purchased extra timber panels and timber rail just incase. Location is South MacLean 4280. Space is 2.8m wide. 1.8m tall.

Looking to get a basic timber gate built and installed on the side of our house. Approx width would be 1.7m. There was a metal fence there previously so it already has some fence posts. Slight incline also. Won’t need it painted, just need it installed

1. Install door closer (pictured) 2. Timber strips screwed into brick to aid function of timber gate 3. Drill. Rick for 4 screws to hang pictures on outside walk

Looking for an experienced handyman/carpenter for a few small maintenance jobs in Manly and Northbridge. Jobs include: MANLY: * Repair and reinforce timber front gate handle/lock area * Timber around latch area has become loose/damaged * One gate requires proper reinforcement/repair * Second gate is still functional but latch plate is becoming loose and should be secured before it worsens NORTHBRIDGE: * Tighten and secure loose basin tap in shared office bathroom Important: * Looking for proper reinforcement/repair solution, not temporary quick fix * Please bring tools/materials required * Experience with timber gate repairs preferred Can be done in one trip/day.

Unfixed palings on bottom of timber gate. Need to be nailed in. Gate latch is also loose and needs to be screwed in. An additional internal door handle to be reduced. Currently loose

I have 2 existing timber gates with a steel frame in Ballarat. I’m looking to install a gate handle or mechanical keypad lock. May require drilling into the frame and aligning latch. Keen for supply & install.

I have an existing timber fence going to a side patio. I am installing the patio roof. After this, I can’t use the existing gate since it is against the pillars. I need to permanently seal this door and make a new door for entry. I am also open to other options.