Find experienced local fencing contractors in Windsor VIC

Looking for someone to supply and install a new side gate and remove/dispose of the existing metal gate. Requirements: * Opening is 840mm wide × 1880mm high * Gate sits beneath an archway, so the top needs to be custom shaped to match the arch * White painted timber with a solid timber frame * Vertical boards with no gaps for privacy * Lock supplied and installed (lockable from both sides preferred) * Must be suitable for outdoor use and close neatly within the existing opening * Remove and dispose of the existing metal gate *supply and install hinges Please include all materials, hardware, labour and disposal in your quote. Photo attached

Hi there, I am looking for an experienced tradesperson/contractor to design and install a custom indoor dog fence. Project Details: Type: Indoor dog safety fence / enclosure Height: 1.3 meters Length: 7.6m Fixing Method: Needs to be securely fixed to the floor. The ground has epoxy quartz flooring, and you can drill holes into it. Design: As shown in the attached picture (needs a walk-through gate with a secure latch) Quote Request: Please provide a rate per meter (including materials and labor), or a rough estimate based on these dimensions.

I have wrought iron gates front of house. Need to install electric motor on existing gate for my car.

shared fence with neighbour is leaning. The fence is standard wood, about 7 metres long. The fence is 9 years old and in good condition, except for the lean! The fix for the lean is a few new fence posts - 3 max, potentially concreted into the ground, which would straighten the fence back to where it should be. We are looking for some quotes to get the job done.

Partial fence repair and letter box replacement

A chunky style timber paling fence needs anchor supports to bring it back into alignment due to leaning

Replace 2 sides of our fence (maybe a third) One side is the blue/ green One side is back down an alleyway

Wooden gate and 2 posts need to be removed and replaced preferably with stel posts and new gate

Paling fence (approx 20 metres) long needs a new plinth (not all of it) and a couple of rails to make it secure. It needs a few nails in places too where the fence is a bit bowed. The plinth is rotten in parts and I am worried that the fence will fall down in a big wind. I have been told that I will need a new post as well so I it might be good for someone who is keen to come by and look at what exactly needs to be done. With that in mind, I have upped the budget. Essentially, make the fence secure where necessary.

Fence panel has fallen away from the wind. Horizontal railing supports needs to be reattached.

Fence is in need of repair. A couple panels need replacing and a top rail needs reinforcing. The posts need some form of L brackets attached bolted into concrete ground. Back gate needs hinge lifting and a new deadbolt attached.

I need someone to come help clean up my backyard and build a chicken enclosure

Two dents in stainless steel panel on building facade. One ~15cm in length, and the other ~24cm in length. Cannot get behind panel, so will therefore likely be similar to refrigerator dent removal.

Where the two fences meet is starting to fall slightly, probably by about 30cm or so, leaving a gap in between the two fences. Need them brought back together, and perhaps a pole in the ground for the fence to hold onto so it doesn’t happen again? Need it done before tomorrow if possible.

A Plinthboard needs repairing on timber paling fence gate inorder to close gate

I need someone to fix a leaning fence by putting a couple of extra posts in and some cement to secure the fence

Construct two sections of paling fence. One section is 12.5m long and 1.8m high. Second section is 6.2m long and max 1.6m high, sloping lower at one end. Include removal of old paling fence in quote.

We have a skip which can't easily be rolled out through a gate because at its widest point the skip is too wide. I just need a ok small section of the timber post cut out to allow the bin to pass. Should be a 10 minute job with the right tools

Replace 2 support posts for side fence Attic 2 meters- existing posts are rotten

Side gate swollen and will not close