Find a fence installation professional in VIC

9m colourbond fence install and removal of old timber fence. Existing fence not on slab

Need fence installed for a new build corner lot. 25m one side, 19.3m on the other. 6m at the back required to complete neighbours fence. Corner side offset is 3.4m, so need also need a 1650mm slatted colourbond gate. Remaining 1750 to be standard timber fence. Happy to provide plans.

Privacy screens 2 attached to wooden gate 1 on side of stone wall 1 on wooden fence rail 2 wooden fence extensions

Broken timber fence needing to be replaced identical to opposite side fence - approx 14m long

Would like brick fence removed including pattern pavement as shown in photos and side wall of brick and replaced with 1.5 m picket fence as shown in photos as well. The length of fence is 6 metres

2 fence posts are snapped. 0ne in the back is right through and the fence is leaning. Posts need to be replaced and fence straightened. One in the front is not as bad and the fence is still straight.

I need a fence installed on one side of my house, along with small side gate and possibly some repairs for the back fence.

I’m replacing the front timber fence (~19 m long) and reinforcing the driveway gate section. Most posts are in good condition and will stay in place — only 2–3 timber posts need replacing (I already have spare matching posts). I’ll also supply two galvanised steel posts for the driveway gate, plus all timber slats, plinth boards, screws, concrete, and oil. I’ve already prepared the site and marked which posts to replace. ⸻ Scope: • Remove and replace 2–3 existing timber posts (supplied). • Set 2 galvanised steel posts (100 × 100 mm) for the driveway gate — no top/bottom rail required, only posts. • Install new vertical timber slats (Merbau or treated pine, 90 × 19 mm) across 19 m span with 3–5 mm spacing. • Install bottom plinth board (150 × 25 mm) and ensure level, alignment, and tidy finish. • Oil/stain all new timber for protection. • Remove and dispose of old fence sections and debris. ⸻ You bring: • Tools (post-hole digger, drill, saw, levels, clamps, etc.) • Skills in timber fencing, concreting, and gate alignment. I supply: • All materials (timber, steel posts, screws, concrete, oil). Budget: 💰 Around $1,400 – $1,600 for labour only (can negotiate). Timing: Flexible — anytime in the next week. Location: Mooroolbark, VIC ⸻ Notes: • Fence height ~1.65 m. • Gate arms will be attached later to the new steel posts (so post alignment is important). • No metal panels or rails — timber slat style only. • Site is clear and ready to start.

Remove and install wooden post on veranda. One has been done already, i need others to be replaced. Materials will be supplied

Fence leaning in few areas on left wall. Need it fixed and bamboo panels installed on top please that we can discuss the cost for separately. Need done today or tomorrow.

Installation of wooden street library. Requirement of post securely into the ground

Install new fence with a door. Total about 7.6 metres long. Accessible from inside and outside. Please contact for viewing if required. Thanks.

Replace damaged wooden post Can supply materials Mordialloc Area

- install pool barrier and gate total 6m, materials supplied , location : Ashwood VIC , more other odd jobs for fencing and gates, pool compliance job , any add ons can discuss further

Fix a section of fencing that is leaning and requires replacement.

4 x fence extension to be installed to wooden fence. Fence extensions supplied just need installation

We have a side fence on our back garden that needs repair or replacement. Height 175cm palings Length 720cm The 3 spans are approximately 2m, 2.5m, and 2.75m between the vertical posts. The posts are hardwood and solid and are set into concrete and brick paving. The cross beams and palings are rotting and degraded. You could probably just replace the cross beams and the palings to repair the fence rather than complete replacement.

Replace and install Ring gate latch on iron gate. Guessing it should be welded on or with small screw and bolts.

I need 2 cypress fence post ( 2.4m post 125x125) installed to form part of a new front fence. The posts need to be installed to the specific height, width apart and angle to ensure they align to a new gate and existing fence. - i have dug holes to 600m depth - I have purchased both post, primed - I request that concrete and crush rock is supplied along with any levelling/laser equipment required Seeking a trade who has experience with installing picket fence posts. Once posts are installed, There is a further stage I will seek help with after concrete path has been installed. I will explore a seperate quote once this job has been completed

I need a tradesperson to fix the pool fence gate hinges at my property in Kew (3101). The pool gate was flagged as non-compliant in a recent safety inspection. The issues are: The gate does not reliably close and latch from any position. The gate does not close properly when a small force (about 250g up or down) is applied near the latch. What needs to be done: Adjust the hinge tension so the gate self-closes and latches every time. If the hinges cannot be adjusted, they will need to be replaced with compliant self-closing pool gate hinges (hinges must be at least 900mm apart or fitted with non-climbable caps). Goal: Make the pool gate fully compliant with AS 1926.1 – 2012 standards so it passes reinspection before the due date. Please provide: A quote for the adjustment or replacement. Confirmation that you have experience with pool safety compliance.