Find a local brick fencing contractor in VIC

Need bricklayer to repair damaged brick fence as per photos located in Niddrie.

This is 15ish meters brick Fence. I need someone to demolish it and take the rubbish. Ensure clean area after the finish.

Brick layer needed to fill in a 2x 1.5m wall where a glass window used to be And to cut a brick fence in two places (1.2m high and two bricks in width)

Demolish and removal of brick fence and associated footings at front of property. As per photos, the fence is in 3 sections with 2 x seperate columns and 1 x main section. Column 1 1780x360x360 Main Section high point - 1780 x 360 Low point - 1150 x 250 Total width - 3940 Column 2 1780x440x240 Cost to include removal of all debris, and leaving the area clean and filled to allow installation of new aluminium fence. Care required to avoid damage around nearby tap and footpath, and must have appropriate experience and insurances.

Build brick fence on existing foundations

Rendering work needed for brick fence

We had someone damage our short brick fence and two front pillars, we need this replaced and fixed, with same bricks to match rest of fence.

Brick fence needs repairs hit by a car still have bricks

About 10m length brick wall fence footing -concrete job

Repair corner of the brick fence

We have a job in wheelers Hill Excavation and footings have been sorted. The plans show a little different, the write up below is most updated. 7 piers 470 x 470 Double bricked 1000mm high from ground level 1 pier with mailbox insert 4 dwarf walls Approx 1400mm long 800mm high from ground level Double bricked Exisiting retainer wall Add 2 courses of bricks Total approx 90 bricks Bricks all on site (600 of these need to be cleaned) Concrete on site Sand on site Builder will confirm about any steel required in brickwork (we have plenty onsite) My guys will render the brickwork and install cappings. Wanting the job done asap

remove a brass name plaque 245mm x 408mm that is glued to a brick fence. Once removed the area will need to be cleaned

Looking for an experienced bricklayer / concreter to demolish and rebuild 2 x structural brick fence piers to a specified brief. Scope of works: Knock down and remove 2 existing brick piers Excavate and construct 2 new reinforced concrete footings. Rebuild brick piers and core-fill as specified Pier dimensions (each): 1500 mm high 360 × 360 mm Footings (each): 800 mm deep Pad size to suit pier (approx. 600–700 square) Concrete: N20–N25 Reinforcement: Reinforced footing cage, N12 deformed bar, 4 vertical bars, N12 closed ties @ ~200 mm centres, Minimum 50 mm concrete cover Steel posts: 1 × 100 × 100 × 4 mm galvanised SHS per pier. Post embedded 600–700 mm into footing. Post tied into reinforcement cage. Posts must be plumb and set before concrete pour. Pier construction: Brick piers built around steel post. Core backfilled with N20–N25 concrete. Brickwork tied to steel post. Piers to be square, plumb and ready for future gate automation Important: Structural steel carries gate loads — brickwork is non-structural. One monolithic concrete pour per footing. No dynabolting or post-install chemical anchors Access: Good Start: ASAP

Looking for a bricklayer/landscaper to build a front brick fence, similar (not exactly the same) to the AI-generated design. I’ve attached a photo of my house for reference. Scope includes: * Brick fence at the front * Brick garden beds aligned with each step * Brick mailbox/parcel box Steel fencing is not required. I can supply materials if needed, but happy to get quotes both with and without materials. Also need soil filling once the fence is completed.

Need someone to remove the render on this low brick fence, looking to refrain from any damage to the bricks underneath. Fence is 6m long and 400mm wide at pillars.

Price to rebuild fallen brick fence. Only fallen parts.

Hi, We are looking for an experienced bricklayer/builder to construct a brick fence. Scope of work: * Build a brick fence approx. 12 meters long and 2 meters high * Proper footing/foundation as required * Ensure solid and straight structure (long-term durability) * Advise on best materials and construction method Important: At this stage, this job is for the fence only. We are planning to install a pedestrian gate and driveway gate later as a separate job, so please allow for this in the design (openings, posts, etc.). We are open to: * Supply & install OR labour only * Suggestions on cost-effective options (brick, block, render, etc.) Location: Maidstone, VIC Timing: Ready to start soon Please include: * Your experience / past projects * What is included in your quote * Estimated price * Timeline Photos of similar work would be appreciated. Thanks!

Replace metal edging and render brick fence ready for painting

Looking to get a brick fence taken down as there is a lean and it needs to be made safe. Can organise skip and removal of the bricks just need the wall to come down. Main wall is Main wall is about 9.4 meters and post is 0.73 meters. Height is 1.86 meters Metal gate can be removed prior. Please provide me with your prices as I haven't sourced quotes yet.

Remove the brick fence, we will arrange the skip. Looking for demolition experts.