Find trusted local electricians in Mount Waverley

Replace an indoor light fitting

Needing a qualified and insured electrician to pop over and connect a new truck tail lift two button pendant controller to my Hino 300 truck. I'm being told it's "plug and play" but can't get it to work, Ive also been told it needs an electrician- I need help please. We are replacing a damaged one, the new one is not plig and play and needs to be connected. I have 2 x controllers I'd like connected I'd we can please.

I need a second power cable run from my solar panels to the inverter.

Byd ev 7.5kw charger installation in garage

My recliner is stuck and electric has failed

I’m looking for a licensed electrician to carry out electrical work at my commercial bakery in Mount Waverley. Scope of work 1. Install a new dedicated 32A three-phase outlet for a commercial Hobart oven * Approximately 10 metres from the main switchboard. * Supply and install a 32A 5-pin three-phase outlet. * Install a new dedicated circuit breaker and all required cabling. * This circuit is for a Hobart commercial oven (415V, 3-phase). 2. Install a new 15A single-phase outlet in the rear work area * Approximately 15 metres from the main switchboard. * Supply and install one 15A single-phase outlet for future bakery equipment. * Install all required cabling, protection devices and circuit breaker. * Please ensure the installation complies with Australian Standards. Requirements * Must be a licensed electrician. * Quote must include all materials, labour, fittings, sockets, breakers and installation. I want a complete, ready-to-use installation. * Please advise if any additional work is required after inspecting the site. * Provide a Certificate of Electrical Safety (if required).

I need to put in 12 downlights and have our pendants replaced in the kitchen We live in a 2 storey house See photos

Need an electrician to put a 32amp wiring for an induction cooktop.

Need removal of island benchtop Need to have plumbing capped and GPO set aside for new benchtop Solar panels need to be removed from the roof. Already disconnected from isolators No need to dispose

Replace existing light switch making a buzzing sound in the light fixture

Need to repair/replace three Classic 2 Gang Switch and one PowerPoint Double GPO switch

We have 16 to 20 downlights upstairs and downstairs. The ceilings are high 4 m and so a tall enough ladder is required to get there. It’s just changing it from bright white to one white setting which is a flick switch on the inside of the down light we’ve been able to change all the ones with the low ceilings with no problem

Timberflame Radius (IB35ETR and IB35R) Gas Heater - would like a gas safety check and need electrical wiring connected which I think is somewhere underneath house.

My Hager 16A RCBO (Power 7) trips immediately and cannot be reset. I've already completed the following checks: • Unplugged all appliances connected to the affected circuit. • Turned the hardwired fireplace fan wall switch OFF. • Switched the RCBO fully OFF and then back ON to reset it.

Please read in full before you offer. **Tesla Wall Connector Installation – Mount Waverley** Looking for a **licensed electrician** to install and commission a **Tesla Wall Connector** at my home in Mount Waverley. **Existing setup:** * 63A three-phase garage sub-board. * Tesla Wall Connector to be installed approximately 1–2 metres from the sub-board. * Charger hardware is supplied by me. **Potential requirements:** * Dedicated 32A or 40A circuit with appropriate RCBO protection. * The existing sub-board currently has only 2 spare module spaces, which may not be sufficient for the required RCBO. * One option may be to relocate the existing 10A smoke detector RCBO to an adjacent circuit (if compliant and safe) to free up space. * If this is not feasible, a small extension enclosure/sub-board may need to be installed beside or below the existing board to accommodate the dedicated RCBO and charger circuit. **Scope of work:** * Assess the existing board and recommend the most suitable compliant solution. * Supply and install all required electrical materials, including RCBO, cabling, enclosure (if required), and associated hardware. * Install, test, and commission the Tesla Wall Connector. * Provide a Certificate of Electrical Safety upon completion. * 3 phase charger Please include your proposed solution and any additional costs for materials in your quote.

Need long ladder to install one of the cameras

Hi there is a crack in the current light . I’ve ordered a new glass piece and it will be available by next Monday . I need an electrician to take it down , replace the light and fit it back in . How much approx is it for a light fitting ? Here is a photo of it ?

Socket burnt out to be replaced with similar double plug outlet

My son accidentally broke the glass in the light in the bathroom. We are moving out next week and I need to replace it or replace the glass asap . Can anyone fix this ?? Or know where to buy a new one exactly the same one ?

Remove and replace 6 downlights, I can purchase the necessary lights from Bunnings based on your advice