Find trusted local electricians in Gordon NSW

I just need a double GPO supplied and installed on timber skirting. Reasonable underfloor / crawlspace access. Must be a Mon, Wed or Fri and need it done by 7th March. Neat job valued. No idea as to cost, my figure just a guess. Thanks!

We just had an electrical awning installed on the roof of our deck. We just need an electrician to connect it to the power. Photos attached.

We are having a pre-fabricated 3.5x5m gym/shed built in our yard this week and need the electrical components added on Wednesday. Mains power is already at the site and we need; 3x downlights, 3x GPO and 1x 3.5kw split system a/c installed

(1) replace double power point electrical wall socket in dining room with a new one (2)in a different room, close existing power point and replace double point power point wall socket, moving it one metre away from existing one (3) tighten electrical wall socket in living room

(1) replace double power point electrical wall socket with a new one (2) replace double point power point wall socket and move it by about 1 metre. Cover old point.(3) Tighten a wall socket that’s coming off. These sockets are along wall skirtings just above the floor.

1 remove the light fittings, switchboard and power points from existing wall 2 After wall is rendered and painted reinstall switchboard and power points on the wall and reinstall light fitttings on ceiling

I have an existing premise which has electricity however I require four more double PowerPoint to be installed by licensed electrician. You can go to the premise this afternoon to see the job and either completed today or tomorrow

1 Install 3 x DC ceiling fans Hunter Pacific 52” with light in place of light fixtures and 1 ceiling fan separately 2 Install IP65 power point for pool pump

this is the lock for the electrical meter room at the level of my apartment, currently nobody got key and cannot access to meter reading - Due date: Before Saturday, 9 December 2023

Install lights and outdoor GPOs. 1. Install 2 lights on front door add switch and light sensor/timer 2. Add IP65 GPO outdoors near electrical box 3. Replace light fixture in living room with bar lights 4. Replace old light fitting with sensor floodlight 5 Install driveway light & switch 6 Add IP65 GPO on deck - Due date: Flexible

1. Replace bathroom exhaust fan 2. Reprogram or disconnect outdoor sensor light that is malfunctioning - Due date: Needs to be done on Saturday, 4 March 2023

lnstalling 3 phase 32amp electric power to the new coolroom - Due date: Before Monday, 30 January 2023

We would like someone to assist in installing a DIY light fence. Digging holes, measuring where holes go, digging up plants and re planting them. All day Saturday and all day Sunday ideally but part of the day or either day would be ok. Just 1 person needed. We are 12 mins walk from station. U need experience digging, experience in garden. U don’t need equipment $35 per hour = $280 per day - Due date: Needs to be done on Saturday, 3 December 2022

Kirby vacuum electrical is not working - Due date: Flexible

Hi, Lights in house no longer working after switchboard tripped. Power sockets OK but no lights.

I have a Tiffany lamp in which the electrical wire has a switch on it and it doesn’t work I suspect the wiring to be faulty and the lamp needs to be re-wired. I have changed the light bulbs several times. It is clearly the wiring. - Due date: Flexible

2 LED ceiling lights simple installation required by an electrician - Due date: Flexible

Hi there We need the following completed 1. A replacement of 2 x wall mounted lights 2. A replacement of 2 x ceiling mounted down lights 3. Check installation of 2 x pendant lights 4. Check some exposed cabling.

Configure Meter Box so an existing domestic electric hot water heater (tank) is fed from off peak controlled load 1. I understand this involves adding an off peak time switch. Hot water is presently protected / connected to a circuit breaker on a common rail in the Meter box on side of house. Meter box is easy access standing and in very good condition and clean. Box is steel and circuit breakers protrude through a white plastic faceplate with cut outs. Plenty of room in the box. I will complete the Origin application to have the existing Ausgrid Meter changed (after your work is complete) to a new smart meter.

2 heaters to be installed in my deck. Lower ceiling but a 4-6mm cable needs to be run from the main.