Find trusted local electricians in Roseville

Install 12m NBN conduit from boundary to house. Please dig a bit more on boundary side so the conduit can be hidden under bitumen.

Need a licensed electrician or experienced ventilation installer for an older house in Roseville. Looking for someone with experience in: • Subfloor ventilation systems • Inline fan / ventilation installation • Older house ventilation & moisture issues Owner will supply the ventilation system / inline fan. Please only respond if you have previous experience with similar ventilation or subfloor airflow systems. system will be supplied by owner.

Various jobs: 1. Lift lights closer to ceiling (cut pole), 2. Fix under bench LED, 3. Fix 12v patio light, 4. Fix Ceiling LED, 5. Recess tv cable in wall

Hi there, I’m looking for a fully licensed electrician to replace an existing 10A Double Power Point (ODPP) with a 15A (Outdoor DPP) outlet. This will be used for EV charging in an outdoor carport. Job Details Replace existing 10A double power point with a 15A ODPP outlet *I will provide the 15A ODPP * Outdoor carport installation *Approx +/- 12m of cabling (or new circuit) is needed from the outlet to the main switchboard. The current wiring run goes across a garden bed — the carport is on the left side of the house, and the main switchboard is on the right side. Must be completed by a licensed electrician who can provide compliance documentation if required. What I Need From You *Labour to remove the existing outlet and install the new 15A outlet. *Any additional wire/circuit or upgrades required to safely support 15A load. *Safe and compliant installation suitable for EV charging **I am happy to work around your availability , preferably this week or next.

I need an existing wiring wired to a new socket and cover which has been damaged. Job is to attend site with replacement cover and install and attach to wall.

Power not working. Lights are ok but one powerpoint arching

A couple of outdoor power sockets don’t work. Also skylight windows lost power.

Hi, I need a licensed NSW electrician to upgrade the consumer mains from my network connection point to the switchboard, and to bring the switchboard up to current compliance. Photo of current setup: /please see attached Existing mains: ~6 mm² Required: Upgrade to 16 mm² minimum Work Required: • Install new 16 mm² consumer mains • Update main switch/service fuse as required • Bring switchboard up to AS/NZS 3000 compliance (RCD/RCBOs, correct labelling, tidy wiring, and any required upgrades) • Ensure solar / dual-supply circuits meet current rules • Provide CCEW and testing You Must Be: • NSW licensed electrician • Experienced with consumer mains + switchboard upgrades Timing: Flexible — ideally ASAP and in the next 1–2 weeks. Please send your quote (or inspection fee) and availability. Thanks!

Just had gyprocking done, need two lights installed and also holes precisely cut out within the ceiling of the bedroom measurements are provided from the Gyprocker

Need license electrician to supply and install a new inline ventilation system under subfloor. Remove,discard and replace it with a new inline fan. Ensure the fan is properly secured with anti vibration mounts if needed.Seal all duct connections with foil tape or clamps to prevent air leaks.Tidy up and secure any loose electrical cables and insulation.Need the tasker to investigate before supply the right fan.

Need to install 7 light switches and 1 light fixture

Need to install new outdoor lights. 2 x Floodlights on house corners (Back and Front) 3 x up / down lights on front of the house 3 x front fence lights (9m trenching needed) 2 x flat LED replacements 1 x Spotlight All lights fittings supplied.

5 units to be tested and replaced if necessary

Bathroom electrical work exhiast fans (x2)

Taking out the old towel rail and replacing a new one

Leaking skylight. Minor repair required. Water has damaged architrave which will be repaired by the painters starting on Monday 14th April

Licensed Electrician Needed – Install Dedicated Circuit Commercial Oven (Roseville, NSW) Looking for a licensed electrician to install a dedicated 40A circuit for a commercial oven (6.66kW, 27.8A @ 240V). The job involves: • Assessing the existing wiring to determine if it is sufficient for the oven’s power requirements. • Running 20-30m of 6mm² (or larger) cable from the switchboard to the laundry through the ceiling (if required). • Installing a 40A RCBO/safety switch in the switchboard. • manhole access to ceiling • Ensuring compliance with AS/NZS 3000 wiring regulations. • Providing an electrical compliance certificate upon completion. Please provide a quote including labor and materials. Must be fully licensed and experienced with high-powered appliance circuits. Available to complete in the next couple of weeks.

Want to install an electrical swing or sliding gate for driveway, need a quotation.

Need to rewire a table lamp. I have some of the parts needed for this (e.g. light bulb socket, plug, cord) Photos of the lamp are included with the old wiring. I bought the new rewiring kit on ebay as I thought I would be able to do it myself, but it's a bit over my head. Not positive whether what I bought is everything that is needed to rewire. For example, not sure if I need a ground wire as the lamps base is metal.

Power to external pool house is tripping fuse. Suspect reconnection/rewiring required to fix.