Find a professional cement sheeting contractor in NSW

Tiny home requires cement sheet and tiles in shower bay approx 1.2m square.. cut around toilet and install to drain to waste.. currently levels not right and water isnt draining to waste. All offers must include tiles, (as pic or equal) cement sheet, adhesive, grout

We have a cement sheeting fence along the back of our property. We'd like it painted in white to make it look a little tidier. We will supply the paint. Dimensions: Back Wall: Height: 2.3m / Width 10m SIde wall: Height: 2.4m / Width 1.8m

Convert Gazibo to portable kitchen . I want to cover concrete area about 2 meters to put one post and put the sheet and cover side wall with cement sheet.

Need old yellowtongue renove in shower area, 1400 by 1100mm New fc sheets installed. Waterproofing flange installed. Materiels supplied.

Need to install 2x(1.2mx2.4m) James Hardie villaboard fibre cement sheet to the wall in the garage for extra fire protection behind the solar panel battery. Need someone who is experienced.

Mount 7 hooks, each has two screws each. 900mm high. Into fibro cement sheeting. Please provide fixtures (anchors and screws).

Supply and install FC sheeting over the top of service panel area in kitchen. Size approx 1600mmx 760mm. Installation to be completed by 11 am Tuesday 17 Feb

I'm looking for someone to build a fireplace hearth in a small area in our home.

Need supply and installation on a fiber cement sheet that got damaged. Size is 3000 x 860 mm. Will need to supply and install

The cement sheeting under our eave has cracked and now has a hole. It needs to be cut out and replaced with a join and then painted white. We have the white solar guard paint for outdoors

1. Supply and install cement sheeting on outside of timber Shed with dimensions 5.45m Length, 3.2m Width and Height (2.3m-2.63m). 2. We need supply of any necessary materials: Cement sheets, fixings, plaster etc... 3. Sheets should be joined with cement/plaster (preferred) or cement sheet joiners or another solution and be ready to paint. 4. Existing Shed is made of a timber frame and plywood and timber exterior. Interior has been Gyprocked.

One of our fibre cement fell down and needs replacement. Size is 3000 x 860 mm. Will need to supply and install

Remove cat door and patch - external will need New fivre cement sheet

Pick up and take away rubbish. Wood, cement sheeting (not asbestos), tiles, 1 x old blind, 1 x small book shelf bracket. Only accept if you can take all.

Repair small section of rendered fibre-cement cladding (approx 20cm). Needs patch and one coat paint to match existing as close as possible.

Just need someone to finish off this sanding that was half done. It’s nearly there just need the final finish to be done. Only 1 big join and a couple on the back. Can supply electric handheld sander. Honestly an hours work probably not even.

Fill up the hole for extra if possible Gluing back with nicknail glue

Seeking a qualified and experienced carpenter to carry out minor encapsulation work on bonded asbestos cement sheeting at a residential property in Lake Heights, NSW. Scope of Work: Encapsulate/cover approx. 3 sqm of broken bonded asbestos cement sheeting located: Next to the manhole on the right side of the property (fake brick wall panel) In the roof space (partial cement sheeting) Covering of damage roof sheeting in the garage Materials presumed to be non-friable (bonded) and in broken condition Total affected area is under 10 sqm, so a licensed asbestos removalist is not required Work must comply with NSW Work Health and Safety regulations and asbestos management codes of practice Requirements: Must be a general carpenter or tradesperson with experience in working around asbestos Site access and briefing will be provided Preferably available to perform the work ASAP Notes: This is not a removal job—only encapsulation/covering to prevent disturbance Clearance certificate not required, but work must be tidy and secure Please include your experience, availability, and quote in your response.

We have already sheeted the front wall and have done all the joints on the front. We are looking for someone to do the one on the back in the same way, tape and patch using joint compound. We are not looking for perfection. Just a decent job. The work is to tape, patch and sand ready for painting. Approx 30 metres of joints plus screw holes to be plugged.

Repair of timber on front