Find experienced local carpenters in Werribee

I am looking for a Cabinet Maker who can build a shelf and drawer under the bathroom sink. I have attached photo for reference. Ist photo is what am trying to achieve the second is the current situation

Need to paint/stain this window (front exterior only) Quote for full job including material and labour. The current finish is Intergrain Natural Stain in colour V9 (as per builder color document) — I’d like this matched or refreshed for a clean finish that protects the timber.

I have purchased 2 × IKEA PAX wardrobes, each 1000 W × 580 D × 2010 H, and I need an experienced carpenter/plasterer to turn them into a fully built-in wardrobe appearance, similar to the photo attached. The PAX units will be positioned together in an existing wall recess. I need the wardrobes put together, framing & plastering, and finishing work with cornice and skirting board completed to house them. I will do the painting. I'm happy to purchase the main materials (Timber framing, Plasterboard) , or alternatively I'm happy for you to supply materials and include them in your quote.

Needing multiple tasks done. Can be done at different stages. Study Walk-in Wardrobe Cabinets (above fridge) Walk-in-Pantry

Need stainless steel fabricator to do food truck fit out, half of it it done just need the remaining

Hi, I need a carpenter/handyman to finish off an opening where an old sliding door frame was removed. Looking to get timber casing and architraves installed around the opening to conceal the exposed studs and brick edge. Wide 2.4m and the high around 2m. The cost include the material

I need a cabinet maker / carpenter to build and install one overhead cupboard in the empty wall space above my fridge (see photo — area circled in red). Melbourne Werribee. What's needed: One overhead wall cabinet to fill the gap between the existing overhead cupboards and the wall/return, sitting above the fridge Must match the existing cabinetry: same dark woodgrain melamine finish, same door style, same edge banding and the same brushed chrome bar handle Doors and gaps to line up with the existing run — top of the cabinet, door heights and reveals should be flush and consistent so it reads as part of the original kitchen Things to consider: Finish match is the priority. The existing doors are a dark woodgrain (likely a Laminex/Polytec board). I'd like the tradie to identify the closest decor match, and colour-match at the supplier before ordering. Please confirm in your offer how you'd handle this. Chrome wall fitting. There's a round chrome outlet on the wall inside the cabinet zone (appears to be a gas bayonet or water point). It can't be covered over. The cabinet needs to be set out around it with an access panel/cutout. Fridge clearance. Cabinet base must leave enough clearance above the fridge for the door to open and for heat to vent. Please confirm the height you'd set the base at. Depth. Recommend if its better to match the existing overheads' depth or: run deeper to the front of the fridge — happy to discuss. Ceiling/cornice. Recommend the height to match the existing or extent to ceiling. Fixing. Must be securely fixed into studs/noggins, rated to hold normal kitchen storage. Internal shelf/shelves: 2 fixed shelf Please include in your offer: Whether your price includes materials, doors, hardware and installation Lead time for the door/panel to be made Whether you'll do a site measure first (happy for you to come and quote in person) Any relevant photos of similar cabinet matching work

purchas of X2 hollow wooden wardrobe doors. Measuring 605 x 2316

I’m looking for an experienced cabinet maker to renovate my kitchen in Werribee. Scope of work: Remove old kitchen cabinets Supply and install new cabinets and drawers New laminate or stone benchtop Install pantry and overhead cupboards Cut-outs for sink and cooktop Ensure kitchen is ready for plumber/electrician if required

Need a qualified carpenter to hang 6 new hollow-core internal doors in a 1970s home in Werribee. A previous tradie botched this job — the handles were at a non-standard height that sits outside the Hume door lock block, so the latch in the jambs are in the wrong spot and need making good. What's involved: Take the 6 existing doors off and stack them on site — I'll dispose of them Fill and sand the old latch mortices in the jambs, flush and paint-ready (I'm painting) Hang the 6 new doors in the existing frames Handles and latches at standard height, aligned to the lock block Consistent 3mm margins, doors closing flush and latching properly Attenton to detail and clean up required. I have all the doors and hardware (handles, latches, hinges) — some hardware is already fitted to the doors. You'll need: Cert III in Carpentry or equivalent, with internal fit-out experience Your own tools that will ensure a proffessional high quality job. Strong reviews for door hanging or similar joinery In your offer, please tell me how you will complete the job to a high standard.

Needing a desk built for a computer setup, need good width and under it a place for a power board and wires to be hidden with a hole. 2300 x 900 roughly. Preferably black or charcoal timber

Wanting a temporary / timber wall or plaster of cladding built so I can hang my brand and sign on led on it. Photo is original, and second is an AI photo. Where the martosworld and charcoal wall is, want a nice feature wall there infront of the curtains if that’s doable! Cheers

need supply and install - plain white overhead cabinets with finger pull to ceiling 2.7m high 2.1m length

Old kitchen Cabinets. the 2 corner double doors came off. Got hinge repair plate and new hinges. Board is weak. Need experienced person for the job. Also 2 middle door hinge need to be refixed with hinge repair metal plate to make it strong

I want making a bookshelf on living area.

Looking for a professional cabinet maker to make garage storage cabinets with black trimmed sliding doors. Refer to the attached photo for the design. Measurements 4m x 2.4m

Need a carpenter to repair a cavity sliding door. It’s still functional, but it’s becoming tight to operate and has some wobble when opening and closing.

Looking for an affordable solution. The goal is to replace the damaged benchtop section around the sink and the water-damaged cabinet side panel underneath. An exact colour match is not essential if it is difficult or expensive to achieve. I’m open to cost-effective alternatives that blend reasonably well with the existing kitchen and are in good condition. Please provide your best price including labour and materials, and advise on the most practical repair option.

The fridge is too wide for the current enclosure. Need to remove the right side of it to fit it in.