Find experienced local carpenters in Reservoir VIC

The timber fascia board that my garage gutters are attached to has rotten through. Looking to get this replaced to fix the sagging gutters. Garage is single storey and approximately 6m long.

Redo kitchen doors and bench top and some cabinetry for tv unit

Would like help removing old benchtop and replacing with wood laminate. I’d also like a 40cm cabinet installed to the left of the kitchen sink. It will need a different plinth to fit the height of the rest of the cabinets. All items will be bought before hand from Ikea.

Need to install floating shelves in kitchen and shelves in laundry room. I do not have the raw material, needs to be provided by tasker. Would like to get quotes.

I’m looking for an experienced carpenter to help with a bathroom renovation. Scope of work: - Remove the existing plasterboard from all 4 bathroom walls and the ceiling. - Remove the existing shower wall. - Build and install a new 1m x 1m shower wall in the required location. - Prepare the framing/opening and install a pre-purchased, ready-made shower niche that I will supply. - Ensure all new framing is straight, level, secure and suitable for a bathroom/wet area. - Ensure the framing and wall structure are suitable for the plumber and electrician to complete their rough-in work. - Leave the area properly prepared and ready for the plumber, electrician, and waterproofing contractor to complete their work. - Remove and dispose of all demolished plasterboard, shower wall materials and general construction waste from the site. Approximate bathroom size: 3m x 2.1m Ceiling height: approximately 2m

Water damage: replace doorframe and door, deal with some water damage in floorboards outside door. seal all for a wet-room bathroom

I have a new undermount rangehood but the current cabinetry is for a slideout. Have removed slideout rangehood appliance but not current cabinet. Needs new cabinet or alteration that allows for mounting new rangehood. Involves. Remove current cabinet and install New cabinet: 600mm wide 720mm high Depth 350mm-450mm Requires: Assemble/build cabinet with three cut outs: one to dimensions as specified in pictures, one for cord, one at top for chute. I have a flat pack cupboard that may be suitable if cutouts are made but pre-drilled holes were in the way of the cutout.

Need help restoring wood on some of our stair posts

I’m looking for someone to seal the small gaps between the bottom of the skirting boards and timber flooring throughout the downstairs living area of my townhouse. The downstairs is an open-plan kitchen, dining and living area approximately 8.8m × 4.8m (floor plan and photos attached). The gaps are generally quite small but I’d like them sealed primarily for draught proofing/air sealing as the timber floors are cold. Job includes: * Clean/prep the gaps where required * Apply a neat, continuous bead of flexible sealant suitable for the junction between painted timber skirting and timber flooring * Seal around the accessible perimeter of the downstairs timber-floored area * Tool/finish the sealant neatly with minimal visible bead * Supply sealant and required materials * Clean up afterwards I’m looking for a clean, professional finish. Please do not use expanding foam or rigid wood filler. Photos show examples of the gaps and the floor plan shows the approximate size of the downstairs area. Located in Reservoir, VIC.

I am looking for a great carpenter to build a trolley similar to this. I can buy the base, just need the caprenter to build the box with good quality light marine ply so it's not too heavy.

Require to adjust kitchen cabinets to fit fridge

I looking for a carpenter to install timber handrails, I'll supply the timber, I am looking for a experience installer in handrails.

Sand down decking and stained

There is some water damage to this part of the cabinet. I need it removed and replaced and then the door put back on.

Building a breakfast nook bench and install of shelving above.

Need laundry cabinet built - under mount sink - over head cabinets - 1 single door tall cabinet White

We’re looking for a handy person/carpenter with a good eye for detail to help with a range of renovation jobs around our home in Reservoir. Ideally looking for someone local who can pop in as needed over the next few weeks. Quality finishes and attention to detail are really important to us. We don’t currently have the required tools, so hoping to find someone experienced and properly equipped. All materials can be supplied. Jobs include: • Installing VJ panelling on dining room wall • Assisting with removal and installation of laundry cabinets • Installing VJ panelling in laundry (walls + ceiling) • Tiling laundry floor (bonus if you can do this, but not essential) • VJ panelling on study wall • Panelling in entrance hall • Helping build a base for IKEA wardrobe and encasing it for a custom built-in look • Assisting with kitchen installation (flat-pack kitchen, carcasses already assembled) • Building faux chimney breast frame + mantel • Building frame for plaster range hood Looking for: • Strong attention to detail • Reliable and easy to work with • Experience with carpentry/panelling/renovation work • Own tools preferred Hourly rate preferred rather than fixed quote. Please send through: • Your hourly rate • Relevant experience/photos if available • Availability Located in Reservoir.

Please sand down floor board that is damaged, soak and remove pet urine stain using hydrogen peroxide or oxalic bleach once removed re polish floor. I just don’t have the equipment. Small area of flooring ( hallway)

I need to remove an existing kitchen cabinet and cupboards and install a new, larger one.

I recently removed our door panel that usually covers our fridge, because its a bit of a nuisance. I would like to repurpose it to cover the areas around the fridge. The panel is Kaboodle oak latte (melamine faced particle board). I would like someone to measure and cut: 2 x smaller cabinet doors (to go above the fridge) 2 x long vertical strips (to be used either side of the fridge) I would also like the door hinges to be repositioned and installed for the 2 doors. I’ve attached photos to show the existing setup, and a mock-up of what we’re hoping to achieve for clarity.