Find experienced local carpenters in Cheltenham VIC

Have three windows on my old shed where wood needs replacing Location Cheltenham

An experienced carpenter or builder to construct an office/print room within an industrial factory. Room dimensions (approx.): 7050mm (L) x 3150mm (W) x 2570mm (H) Scope of work includes: • Installation of lighting • Power points • Air-conditioning • Installation of sliding doors (doors provided) • Flooring Experience with commercial or industrial fit-outs preferred. Final price/ budget to be discussed upon quotation.

We have purchased a kaboodle kitchen drawer cabinet from Bunnings to replace the old worn out one, it is slightly smaller than the old one, so need a solution to fit it

I have a joint kitchen cabinet which needs to be split in two separate cabinets and install wheels for easy movement.

Looking for someone to build custom cabinetry for our living room. Wall width is approx. 2.4m and height from floor to ceiling cornice is 2.56m See photos for mock up design of what we are attempting to build. Bookshelf down the left side with cupboards for storage above and below wall mount TV. Lower shelving would have a hardwood table top to house a sound bar etc. Not sure if this is the right place to post this job but wanted to see if there is interest and price can be adjusted.

Hi. I’m looking for a cabinet to be built at the end of the hallway. The curved side would be on the right side of the wall. Reference image and hallway image attached. Measurement - 10.40 x 6.20 mm. Open to quotes/offers as I’m unsure what it costs. I would be keen to similar work done in the past. Thanks !

I have a joint cabinet which needs to be split in two separate cabinets and install wheels for easy movement. 3 other drawers need wheels installation. So total 5 set of wheels.

We have a handful of carpentry jobs fixed as follows: 1) Most Urgent: bedroom door repair and paint (split and cracked around latch areas of door frame and door from teenager slamming) needs completing this week 2) cupboard door patch up and paint (a fault with the design of the door as they rub against each other as they open, could look at adjusting hinges slightly so this doesn't happen) 3) plywood panel bog patch up and paint (part of laundry cabinet) hard to photograph since its behind washing machine can show you in person if you get the job for the other tasks. The bedroom door is the main priority to be completed by the 16th, the others asap.

We need an inspection for a white sheet of colourbond white flashing to cover a timber section underneath our balcony edge. It is purely to cover up the timber which has been poorly painted - structurally everything is fine. It is approx 30cm wide and 4m long but need to check size. Please note we are 5 minutes from Bunnings Mentine.

I need a few jobs done around my unit, - Fix the timber peeling in the bathroom sunlight - replace the timber lining the window in a bedroom - - Fix the tiling in the laundry, there maybe some water damaged timber, that will need to be replace I am flexible with the budget, so please send through offers please include in your quote the materials

I need a carpenter to do arcs and skirts on a new wall. 1 x cavity slider requires architraves & few small bits of skirting to be installed Carpenter must be experienced with fix as arcs require buzzing to suit protruding plaster. Job must be done on Saturday 8th All material supplied, just need your own tools

Medium sized bench needs staining and sanding.

Install new timber deck supply and install. Type of timber doesn’t matter as I will paint white 3.5m x 3.5m

Build cabinet, we have tools, photo of what we are building

We have a wood fireplace that needs installation. Link is Scandia Warmbrite 300 Series 4 Indoor Wood Heater. Would like it installed this Saturday. We have everything needed just need someone who has installed one before to come and install it. Price is $50 an hour.

All materials will be purchased, just doing the labour. We need to install stainless steel panelling onto a wall cutting holes for piping so we can reattach sinks. Approximately 10m, panels are already cut, just need to have holes measured and cut and to fix panels to wall.

Looking to hire someone for the entire day 9-5pm to help build and install IKEA cabinets and possible bit of small fixes in the house (door jamb, shaving doors, door lock etc). My partner and I will be there building & working with you. We might duck out occasionally to get a few things from the shops. Ideally you have handyman/ building experience and have your own tools (we have ours just enough for ourselves). Waste bin on site.

We would like a laundry cabinet similar to attached photo made to size (1200x570). First photo is what we want, second photo is what we have. Please give me your quotes.

We have two wardrobes which we have bought 4 ikea pax wardrobes for. X2 wardrobes are H 201 x W 100cm x D 58cm and x2 wardrobes are H 201cm x W 50cm x D 58cm. These will already be built for you. One large and one small will go onto each room. We have pre existing built in robes which we have removed and now there is just the hole and the back plasterboard. We want to move the ikea wardrobes in however there will be gaps and large holes around them and we would like them to be filled professionally. The doors that are on the wardrobes currently are too big and won’t allow for the door to close with the depth of the ikea wardrobes, we would like new thinner doors (like most wardrobe doors) to be fitted/installed please. Please include price of any materials in your quote thank you

We’re looking for an experienced carpenter or builder-carpenter team to build a cyclorama-style wall inside our warehouse in Cheltenham. This will be used for photography and videography content — mainly product, pet, and lifestyle shoots — so the wall needs to be clean, seamless, and professionally finished, with a smooth painted surface that holds up well under lighting. 🔧 Scope: • Build a frame: 4m wide x 4m deep x 3.5m high, abutting existing warehouse walls • Sheet with 10mm plasterboard • Install yellow tongue or similar structural flooring • Create curved corners (approx. 450mm radius) at floor-to-wall and wall-to-wall junctions (only one side wall for now) • Smooth trowel, plaster, and sand to a paint-ready finish • Include initial painting using appropriate studio-grade white paint Ideal Candidate: • Has experience with curved walls, set builds, or studio/shop fitouts • Can show examples of similar past work • Available to start ASAP • Must be able to supply all materials and complete the job end-to-end A site inspection can be arranged. We’re open to reasonable quotes based on experience and quality of work.