Find a reliable appliance technician in Dianella

I have a Samsung fridge (model SRL456LS) and need the door hinge reversed so it opens from the opposite side.

I need a recess made to house a dishwasher

Disconnect old dishwasher and install new dishwasher. Existing cabinets and plumbing in place

1 Hole in Dishwasher cabinet and 1 hole in Laundary Cabinet for washing machine. Property is in Dianella WA

Looking for someone experienced with outdoor pizza ovens or masonry/render repairs. The outer surface of my pizza oven has started to break down due to rain - sand is coming off and a dark layer is now visible underneath. Need assessment and repair to restore and weatherproof the surface.

Oven above has a timber surround but below will be dishwasher and cannot have surround as the cavity is 600mm wide. So just need a nice curved edge from the ground to the oven.

Bosch washing machine goes through the full cycle but with a minute to drain it just tumbles and does not drain. I have cleaned filter but did not find any obstruction.

We would like someone please to connect our washing machine.

Old recliner electric chair with remote not working

Replace the existing gas water heater with the new one

Looking for an security system installer for a Swann 2K DVR 4 camera security system already purchased. Must have and be able to provide Security Installer’s Licence issued by the Licensing and Enforcement Division of the WA Police Force.

It doesn't do a proper cycle and drain the water out.

Samsung top loader. Wash cycle works but the machine will not go onto the cycle or pump the water out. Looking for an appliance tech to quote on repair. Budget is just a place holder

I purchased a new cooktop which is larger than the existing by 10cm so need the stone top recut preferably by wet saw

Current whirlybird is worn out and making squeaky sound. Need a new one to be supplied and installed.

It's leaking hot water from the bottom of the machine. I've checked the seal on the water tank - no issues. I've descaled the machine (and do so regularly). I have researched - could be the brew head, but I'm not wanting to open up the machine to check!

My Nespresso Pixie coffee machine is leaking water. It's leaking hot water from the bottom of the machine. I've checked the seal on the water tank - no issues. I've descaled the machine (and do so regularly). I have researched - could be the brew head, but I'm not wanting to open up the machine to check!

I have a 2017 Tesla Model S and would like to remove the existing air suspension and replace with like for like struts. I can handle the software calibration afterwards but want someone with the right tools to change the struts. Any other details please let me know. Job won’t be done until October(ish) due to shipping of parts.

Alter an existing kitchen cabinets to fit a dishwasher. Existing conditions * The existing kitchen cabinets each have an internal width of 470 mm, fitted with timber doors. * A water filter is currently installed inside the circled cabinet. * The 40 mm granite benchtop is structurally supported by the rear, side separating cabinet partitions, & front cabinet frame. * The partition walls are typically double 18 MDF boards. Refer to photo. * The circled cabinet is positioned between the sink cabinet on left & a drawer cabinet on right. * The sink cabinet is a double-width unit, with 180 mm of clearance from face of the partition wall to the edge of the sink basin. * Water and power provisions already exist within the sink cabinet, but are located at the far end from the intended dishwasher. Scope of Works 1. Remove the existing cabinet door from the circled cabinet. 2. Relocate the water filter to the sink cabinet, ensuring it is securely mounted & accessible. 3. Modify the circled cabinet to create space for 600 dishwasher by: * Cutting the cabinets base flush with the floor. * Shifting the partition wall 150 mm into the sink cabinet, increasing the width to 610+ mm . 4. Alter the affected sink cabinet door by 150 mm, to ensure both doors are fully operable. 5. Install a new water supply pipe, from the existing water provision in the sink cabinet with shut-off tap. 6. Install a new drainage hose, and connect it to the existing sink drain trap. 7. Retain the existing power point if it meets safety & compliance requirements.

To clamp a dishwasher lead and remove a pipe cover.