Find professional window and door services in Camberwell VIC

I have a deep cavernous gap between the brick wall and timber door frame at my front entrance (exterior side only) that needs filling and sealing. Job requirements: - Clean out any loose debris, dirt, old mortar - Brush out dust (wire brush or stiff brush works well) -Use compressed air or a vacuum to get deeper debris out, ensure dry surface. - Fill gap with expanding foam (low-expansion type). - Trim foam once cured. - Install backer rod. - Apply exterior-grade polyurethane or MS polymer sealant. - Finish with smooth, weather-resistant seal, for clean appearance and proper insulation. Looking for someone with experience in this type of repair who has the proper materials and can ensure a professional finish. The gap is quite deep so expanding foam will be necessary before final sealing. Please provide quote including materials. Photos don’t capture how cavernous the gap is, but it was enough for 3 spiders to call it home and I’d like to avoid that situation from re-occurring.

I have 1 wall and 2 door damages to be covered up, to make sure the damage is not visible! Thank you :)

Strike plate needs adjusting. Bolt not sitting smoothly

Sliding door stopped working, seems like the door is now detached from the top hangers

The door is not going up and down properly

Supply and install solution to fix draft coming through door (235 x 82) between garage and into property. Sealing of the door frame edges and the 2.5cm gap at bottom of door.

Remove & replace hinges on a 2 piece, 2 metre high, bifold pantry door. Full overlay hinges provided.

We have an old door hanging in an archway (see photos) and we would like to close this off and create a new door arch (and hang a door we already have) next to it.

The bottom edge banding on two overhead cabinet doors above the cooktop has warped from heat. The door faces are fine. I only want the bottom edges re edged. Do not quote to replace the doors. Scope; 1. Remove both doors, protect benchtop and splashback. 2. Cleanly cut back and remove the warped underside wrap only, leave the front face intact. 3. Prepare the underside edge, square, clean, and lightly sand for adhesion. 4. Supply and fit new plain white heat resistant ABS or PVC edge banding to the underside of both doors. Use hot melt or equivalent cabinet grade adhesive. No contact film. 5. Trim and flush both faces neatly, radius the arris lightly, seal the ends to prevent lifting, and clean any glue residue. 6. Reinstall and align the doors, check clearances to the rangehood and the neighbouring door, and confirm soft close works as before. 7. Leave the area clean Notes. • The repair is to the underside edges only. The colour can be plain white. A close white match is fine as the new edge is on the underside. • Bring 16 mm and 18 mm white edging so the job can be completed in one visit. Measure on site to confirm. • Location is an apartment kitchen near Camberwell Junction. Photos attached show the exact edges to be repaired. Onsite parking available. Requirements for the Tasker. • Cabinetmaker, shopfitter, or handyman with proven edge banding experience. • Provide a tax invoice if required. Please answer in your offer. Confirm you will re edge only, not replace the doors. Confirm you will use heat resistant ABS or PVC edging and cabinet grade hot melt or equivalent. Confirm your availability and parking needs.

Need door opening in bathroom , door jam, stops, and archs fitted, door hung and handle fitted. Door size 770x2340. Not a load bearing wall. All timber materials, hinges and door handle supplied. Labor only.

Looking for a handyman or carpenter who can help install a dog flappy on a wooden door. You will need to remove an old, smaller-sized doggy door, cut a big hole for the new one, install it, and secure it. I have already purchased the dog door.

Paint both external garage doors only as shown in photo. I provide paint, you supply tools. Please paint 2 coats and use a fine roller to reduce texture. I am seeking a smooth finish. Please include offer inclusive of labour, tools and airtasker fees.

Replace broken panel in lead light window

One flush mount panel door W4000xH2400; one roller door W1600xH2400

Replace with toughened glass, dimensions 400×700, with a circular hole of 25cm diameter（dog door）. Installation required.

I'm looking for someone to reconnect flywire to my screendoor. Potentially a staple gun/ feeding it back into the door frame. Having extra flywire just in case would be a bonus but it's not torn I think it's just a reconnect job

Looking for two experienced people to carefully remove two large colonial timber windows this weekend (Saturday or Sunday, afternoon preferred) in Camberwell. These are heavy, multi-pane sash windows and will require a two-person lift. The windows are being reused, so care is essential. What’s involved: • Remove 2 large colonial-style timber windows (see photo) • Gently remove trims, architraves, and sashes without damage • Ground floor with easy access • Help load windows into a trailer (owner will arrive once you’re close to done) • No wall patching or rubbish removal needed When: Saturday or Sunday afternoon Where: Camberwell

Have an old MDF Door outdoor, need to swap it with a new wooden outdoor door. Door and parts will be provided

Our front door has an old mechanism that repeatedly sticks making it hard to open the door. It has been replaced in the past, but it's hard as the door knob is in the centre of the door so the locking mechanism has to be very long. I need assessment of the problem and some information on ways to fix it - and then fixing. Even if that means getting a new door and hanging it.

The door handle has come loose and needs to be reconnected