Find experienced local tradies in London

Install awning over back doors

2 small cracks in front of house render that need filling and painting over.

I’m looking for an experienced carpenter/joiner to remove my existing staircase balustrade and install a new handrail, base rail and wooden spindles as pictured. Current staircase: • 14 steps • Bottom run length: 397cm • Top/landing run length: 286cm • Width approx. 92–110cm • Existing painted timber balustrade with wooden rails and newel posts

Remove old cement render and reapply new cement render ready for painting, including repair of the top blocks underneath the flower boxes.

Need a qualified electrician to connect a 4.5kW sauna heater (BC45, 230V single phase) to an existing dedicated sauna circuit. Most of the heavy lifting has already been done by a previous electrician - the circuit is already installed and live in the consumer unit (B32 MCB on its own breaker labelled “SAUNA”), cable has been run from the board to the sauna room, and a Contactum rotary isolator switch is already mounted on the wall. The issue is the previous electrician hardwired the infrared sauna panels but didn’t connect the main stone heater, which has its own separate cable with crimped terminals that needs wiring in. The heater is already in position and ready to go - it just needs connecting to the existing circuit, either into the isolator or junction box that’s already there. Photos attached show the existing isolator and cable run, the consumer unit with the dedicated sauna breaker, the heater’s cable/terminals, and the heater unit itself. Happy to discuss on-site but it should be a relatively quick job given everything is already in place.

electric gibus awning / line not moving. need to programme a new Somfy Smoove and make sure everything connected to power it so it can move in and out again. This job is to site visit, to supply and programme a new somfy smoove. Any further work to be agreed and charged on top

We are a sauna operator in North London. One of our sauna doors has a timber frame with large glass panel. We are struggling to get it closed and sealing in the heat. We would like someone (a door specialist) to come in and assess and adjust the door - thank you

Site visit to review our electric awning

Need a qualified electrician to hardwire a new Insignia MXOS1700 hybrid sauna inside my home. This is a hardwire-only unit - it has no plug and must be permanently wired to a dedicated circuit from the consumer unit. It's an outdoor-rated model being installed indoors so no external cable runs needed. Electrical Specs (from manufacturer manual): Harvia 4kW stove - 240V single phase 4 x far infrared heaters - 1,320W total (240V single phase) LED lighting, Bluetooth, control panel - 120W (240V single phase) Total load: 5,792W / 24.2 amps 240V single phase only - no three-phase or supply upgrade needed Requires dedicated 32A MCB and 6mm² T&E cable minimum (depending on run length) Scope of Work: Survey cable route from consumer unit to sauna location inside the property Install dedicated 32A MCB in consumer unit (spare way needed - can send photos of fuse board in advance) Run Twin & Earth cable from consumer unit to sauna Install local isolation switch near sauna Make final hardwire connection at sauna's electrical junction box Test, certify, and issue Electrical Installation Certificate (Part P compliant, BS 7671 18th Edition) I have the full Insignia installation manual and Harvia wiring diagram available on the day. Timing: Must arrive by 12pm Friday. Estimated job duration 1.5-3 hours. Note on cable run: The sauna is on the first floor, directly above the consumer unit on the ground floor. They share the same wall, so the cable run should be very short and straightforward - essentially straight up one level.

I have had some issues with damp at my property due to issues with an external render.  I am looking to render one external wall (ground floor) at my property to avoid moisture coming inside.  There are cracks in the render and it measured high in moisture in many places. There was previously a lean to shed which has now been removed.  Instructions are: remove the render back to the brickwork. Treat the bricks with three coats of Cementone Aquapruf then render the wall with a moisture inhibitor in the moisture mix. Ensure that the new render ends above ground level in a bell mouth drip. 

I have a wall that needs to be rendered (sand and cement) . It is a concrete wall that was built during last summer. Only 1 side needs rendering. Tasker needs to provide all materials. Apply mesh and 2 coats of render. I will paint myself. It's 16m by 1m. Easy access to the rear and side of garden. Parking on my drive is available plus permits if needs be.

I need an experienced roofer or builder to inspect and repair damage around a dormer window and roof eaves area. There is damaged render and possible timber/fascia deterioration causing risk of damp and water ingress. Work may involve: • Roof inspection and repairs • Carpentry repairs to fascia/soffit area • External render repair • Checking flashing around dormer window Access will likely require scaffolding due to roof slope. Please provide experience details and availability for inspection/quote.

I have a built in wardrobe with just one sliding wardrobe, i am unable to find where this door was bought from therefore cannot buy the second. I would like to replace the whole built in wardrobe by removing the tracks and the inside (space pro style) rails and would require advice on where to go to purchase a replacement wardrobe that will fit this space. Thanks

Sanding walls and architrave and doors and some minor filler work. Must have 225mm drywall sander. If not please don't offer

Cracks at the front of the house in need of repair.

fix a retractable electric gibbus awning

We have an array of IKEA Pax wardrobes in a dressing room. We would like these moved to a new room and a carpenter to build around them. Design to be agreed but I’d like the finish to be similar to the attached photo.

Hi, I’m looking for a localised render repair on my property in Whyteleafe. I have a few cracks in the exterior cement render, and water is coming in around the window sills when it rains. I do NOT need the whole wall or house re-rendered — just targeted repairs. Could you please provide a quote for: 1. Raking out and repairing cracks in the existing cement render using a flexible exterior filler or polymer-modified repair mortar. 2. Re-sealing around the affected window frames/sills with a high-quality exterior MS-polymer sealant. 3. Spot-painting the repaired areas only to match the existing finish. 4. Confirming what materials you use for crack repair and sealing. 5. Whether the quote includes labour, materials, and any access equipment (it’s a ground floor/first floor property, so scaffolding shouldn’t be needed). For reference, I understand small crack repairs are usually in the £100–£300 range, and patch repairs (1–2m²) £250–£450, with window frame resealing typically £107–£310 per window. I only mention this so we can align on expectations. Could you also confirm: - Your experience with render repairs and water-ingress issues - Public liability insurance - Whether you offer any guarantee on repair work - Estimated time to complete the job I can send photos if needed. Thank you — looking forward to your quote. UPDATE I have added a few pictures the main work is around the 2 round windows and the cracks below, and the downstairs windows, as well as some cracks along the wall.

Built in wardrobe door broken wardrobe doors have come off the hinges.

Old Mitsubishi car (2004), passenger door needs to be taken off, metal/steel plate needs to be welded on, door put back and attached to the metal/steel plate. It doesn’t need to be beautiful but I think you need a gas welder for this kind of work. We have had this work done already in the driver side - please see picture.