Find a professional hot water system contractor in East London

The shower is an electric one and does not produce hot water now. It was working yesterday and now it is faulty. If someone could take a look would be grateful.

We are currently undergoing a house renovation and our gas supply and combi boiler are disconnected for several months. I need a plumber to install a temporary electric hot water cylinder (approx. 100L with immersion heater) so we have hot water for showers and taps during the build. Scope of work: • Install wall-mounted or floor-mounted 100L electric hot water cylinder • Connect cold mains feed to cylinder • Connect cylinder outlet to existing hot water pipework feeding upstairs bathrooms • Install necessary valves, pressure relief and discharge pipe • Connect to existing fused spur / electrical supply for immersion heater (or advise if electrician needed) Context: • Property in London (IG8 area) • Two bathrooms on upper floors that need hot water • Boiler currently disconnected due to renovation works • Cylinder location flexible (loft or first-floor bathroom depending on practicality) Requirements: • Qualified and experienced plumber • Ideally G3 qualified if installing an unvented cylinder • Must supply small fittings and valves required for installation Goal: Provide temporary hot water for showers and sinks during a 4–6 month renovation. Please confirm availability and approximate installation cost.

Main boiler water hot and cold

Our electric shower has just randomly stopped working and need someone to come and take a look at it urgently. I’ve bought a new shower head as I initially thought the issue might have been he hose but after installing it stiill issues - need someone to coome asap - thank you

My bathroom hot water is very low

Some knobs are not working

I have a water pump, but the hot water is very low, doesn’t even fill up a bath

The hot water tap on my shower has stopped working properly. When I twist the hot water handle, only a very small amount of water comes out. Cold water still works normally. This started recently 2 days ago, no visible leaks. Looking for someone to inspect, repair/replace the tap or internal valve if needed.

I've got a couple of heating/hot water issues. 1) The radiators in my flat aren't giving out any heat 2) The hot water in one bathroom doesn't get properly hot, unlike the hot water in the other bathroom (which gets very hot). Apparently the thermostatic valve might need replacing?

New shower was installed, hot water worked fine initially, but the shower mixer needs readjustment as there is less hot water and the temperature controlling dial is loose

replace old Ariston Classico direct hot water cylinder

Only very hot water is coming out of the shower. The thermostatic temperature control (red on the right) is not responding and does not reduce the temperature

I have an electric hot water cylinder with a failed thermo/stat and possibly a faulty immersion element. Can you confirm you’re G3 certified for unvented cylinders (if relevant) and provide a quote for parts + labour including any drain/refill?

The hot water will run hot then cut out and be cold, then run hot briefly and then cold again when running a bath. Last winter after a boiler service, they thought the issue could be the water overheating. The problem stopped in the summer when we weren't using central heating, but is back now. Please can you diagnose and fis the issue.

Need a plumber to fix a broken toilet flush in the upstairs bathroom, and sort the hot water regulator in a Victorian shower. Ideally someone available today, or tomorrow morning the latest.

Shower faucet - only hot water coming through, no cold water

Low hot water pressure from kitchen tap. Normal hot water pressure from bathroom tap and shower, therefore no boiler issue. Kitchen pipes might need replacing. I would like to install a new tap.

When you turn on the hot water tap of the bath not much water comes out

I've just moved in and my hot water isn't working (electric boiler)

I need a licensed plumber to inspect and repair my Main unvented direct cylinder (hot water system). The system is not working correctly and requires professional attention. Scope of work: • Diagnose the fault with the cylinder. • Carry out necessary repairs or replacement of faulty components. • Ensure the system is left in safe working order and compliant with regulations. Requirements: • Must be a qualified plumber with G3 certification (legally required for unvented hot water cylinders). • Please bring the necessary tools and advise if parts are needed. • Work should be completed to a professional standard and the system left clean and tidy. Please confirm your certification and experience with unvented cylinders when making an offer