Hire a reliable appliance service in Sutton Coldfield

We have a cross trainer machine that currently isn't working as the connection for the lead to insert into it has been pushed inside the cross trainer. As a result, the wire from the plug doesn't have a connection point anymore

Hi, I have a washing machine that needs new longer tubes to be attached to the back and secured on the tap. The old ones don’t reach the drain and tap. I don’t know how to do it myself and cannot get the pipe off in the back as it’s on too hard. I need someone strong and possibly with a big wrench in case it is stuck. If anyone is close by the B74 area who could come over anytime today or tomorrow quickly, I’d really appreciate it. I’d give you £20 cash for your service. :)

I think it's a drain pump . I've check and clean , but not sound from the pump. I just want to know if you can fix it or I have to replace with a new one

Hi , I am looking for a specialist to carry out a "ductless-to-ducted" kitchen conversion in my new-build Taylor Wimpey home this February. The current setup is a recirculating Electrolux hood. I am looking for a professional "one-stop" service to vent this externally to a high standard. Technical Requirements: • Diamond Core Drilling: A clean 155mm hole needs to be drilled through the external masonry (brick/cavity/block). This must be done with a diamond core drill (no hammer/chisel) to ensure no damage to the external brick face or internal plaster. • The Ducting: I require 150mm rigid round ducting to be installed through the wall (cut to size). Please do not use flexible foil/hose through the wall cavity as I want to remain compliant with NHBC Section 8.3 standards. • Airtight External Vent: I will be providing a Naber Flow Star GTS 150 (magnetic airtight system) or Luxair automatic airtight system.This needs to be fitted to the external brickwork and sealed with silicone. • Internal Connection: My existing Electrolux hood has a 150mm outlet. I need the rigid ducting connected to the hood motor and sealed using aluminum foil tape to ensure it is 100% airtight within the chimney piece. • Weatherproofing: The duct must be installed with a slight (1–2 degree) downward pitch toward the exterior to prevent condensation or rain ingress. Project Scope: • Location: Kitchen is on an external wall (back-to-back install). • Access: Side elevation of the property. • Timing: feb Could you please confirm: 1. Do you provide the diamond core drilling as part of your service? 2. Are you comfortable installing the Naber magnetic vent system or Luxair automatic vent system 3. What is your estimated lead time and cost for this specific installation? 4. Will you guarantee that my existing MVHR system will not be impacted by the vent and will be airtight I look forward to hearing from you. Kind regards, Anam

my washing machine has broken, ive tried to unblock but it still won’t drain

Washing machine stopped working, the lights aren’t showing but I haven’t touched anything

I need to remove the door of carbinet, take out the dishwasher and install a new dishwasher in

My tumble dryer not heating clothes

I have a freezer which fits under the kitchen work surface and it seems to have either slipped off or broken the base which kept it vertical . It is now leaning forward at an angle and I need someone to restore it to vertical .

My washer dryer is leaking badly its flooded my floor and downstairs neibours ceiling

Washing machine water waste pipe plumbing is blocked and leaking . Don't know if needs cleaning out or replacing

I have a Siemens dishwasher SN65M032/B3 which has an error code E9 which means that the Dishwasher Heat Pump & Motor Assembly needs to be replaced. I am looking for someone experienced to replace the part (already in hand) and I would pay for the labour.

Stacked oven and cupboard above need fitting properly

I have a Siemens dishwasher SN65M032/B3 which has an error code E9 which means that the Dishwasher Heat Pump & Motor Assembly needs to be replaced. I am looking for someone experienced to replace the part and I would pay for the labour & part which is available at espares https://www.espares.co.uk/dishwasher/sn65m032gbc9/dishwasher-heat-pump-motor-assembly/product.pl?pid=5244066&shop=siemens&path=183865&model_ref=13625291

Aeg oven not heating oven only Grill heats ok

My dryer is turning on but the cycle isnt starting

Fix my washing machine its broken

Cobra lawnmower starts runs for a while and then cuts out. Also needs blade sharpening.

Put a microwave bracket on the wall

Pressure washer makes a generator noise then cuts out mid flow and then starts again after a minute or so