Hire a reliable appliance service in Derbyshire

Integrated dishwasher has dropped slightly because bottom support has moved. Door panel now misaligned and won’t close. Needs base support repositioning, leveling and door alignment.

Three Chester draws need fixing

Plumb sink in and leave access and piping for washing machine

We have an integrated dishwasher, Ikea kitchen and Ikea Vaglig front connector. We need someone who can help us put it together as the instructions aren’t very clear!

I would like my copper piping to my dishwasher moved - where I want to move my dishwasher it has the copper piping water feed to it, so it just needs moving behind the wall to accommodate.

My dishwasher is running fine, but the inside items are not cleaned well.

Knocking a kitchen wall down so need to move gas pipe.

I have a Hisense Hi8 HI6443BSCWF 60cm induction hob which has already been professionally installed and hardwired. The electrical installation is complete and no electrical work is required. The hob is a standard surface-mounted installation (not flush-mounted) and the manufacturer's foam gasket is already correctly fitted underneath. There is currently approximately 5mm front-to-back movement because the existing worktop cut-out appears to be slightly larger than required. I need someone to: • Check/measure the existing worktop aperture against the manufacturer's specified cut-out of 560–562mm × 490–492mm. • Secure the hob so that it cannot move within the aperture. • If necessary, use a suitable heat-resistant packing/filler solution to reduce the effective aperture size and properly locate the hob (not on the outside) • Keep the existing manufacturer-fitted foam gasket intact. The manufacturer requires this gasket around the underside perimeter of the glass. • Leave the hob level, centred and securely seated on the worktop. No worktop cutting is expected and no electrical connection/disconnection is required. Please quote including all materials. Ideally looking for someone experienced with fitting induction/ceramic hobs.

I am removing an old gas fire and need to make sure the gas pipe is capped off

Removal of old washing machine & dryer & installation of new.

When trying to light bbq the gass is not coming through properly, very week flame then gose out

I’m looking for a qualified electrician to replace my existing hardwired ceramic hob with a new induction hob. Existing hob: Indesit RI 161 C ceramic hob (6.2 kW) New hob: Hisense Hi8 HI6443BSCWF 60cm induction hob (7.36 kW) The existing Indesit hob is hardwired into a dedicated cooker supply and will need to be safely disconnected and removed. The new Hisense Hi8 also needs to be hardwired, using the existing cooker circuit if it is suitable. Please check that the existing circuit, cable, protective device and isolation arrangement are appropriate for the new 7.36 kW induction hob before connection. The existing worktop cut-out should already be compatible (approximately 560 × 490 mm), so I am not expecting any worktop modification to be required. Scope: 1) Safely isolate and disconnect the existing hardwired Indesit hob 2) Remove the old hob from the worktop 3) Check suitability of the existing cooker circuit for the new 7.36 kW induction hob 4) Install and hardwire the Hisense Hi8 HI6443BSCWF 5) Secure the new hob correctly in the existing worktop aperture 6) Electrically test the installation and confirm safe operation 7) Dispose of the old hob as appropriate for electrical appliance if this is possible or alternatively, load into car for disposal at Raynesway Household Waste Recycling Centre, please let me know if disposal is included in your quote. Please quote for labour and any standard electrical connection materials required. If you anticipate that the existing circuit may require upgrading, please indicate how this would be assessed and any likely additional costs.

Need an integrated fridge freezer uninstalled and removed from its cabinet housing. Requirements: Carefully detach cabinet doors and mounting brackets without damaging surrounding units or woodwork. Safely disconnect from the power supply. Slide the unit out cleanly. Leave the area clear, neat, and ready for a replacement. Looking for someone punctual, with the right tools, and experience handling integrated appliances. Drop your offer and availability.

Iron burn mark needs repairing

I have issues with the thermostat on my commercial fridge

The tread mill is not switching on

Food fridges used for business . There are total 2 fridges.

I need someone to fit a integrated door on a dishwasher

Stopped working completely

Install a cooker extractor fan hood, electrical supply is in place. Tasks in garden: Cut back fence and trim budlea. Empty shed ( there is a small cabinet, a few pieces of wood. Remove all rubbish