Hire a trusted hob installation and repair service near you

I am looking for a qualified and experienced electrician/appliance installer to replace the existing oven and separate hob in my kitchen. New appliances to be installed: Oven: Bush BIBFOSAX Silver Built-In Single Electric Oven (purchased from Argos). Hob: Bush A60CT Four-Zone Ceramic Electric Hob (purchased from Argos). Work required: Safely disconnect and remove the existing built-in electric oven and separate hob. Take away and responsibly dispose of both old appliances. Install and connect the new Bush built-in electric oven. Install and connect the new Bush four-zone ceramic electric hob. Ensure both appliances are properly fitted and connected to the existing electrical supply, subject to suitability. Test both appliances to confirm they are operating correctly and safely upon completion. Please provide a quote for the full job, including labour, installation, electrical connections, removal and disposal of the existing appliances. Both replacement appliances are being supplied by me. Looking for someone reliable, experienced and suitably qualified. Thank you

Need someone to disconnect old gas hob and install new electric hob

Fit kitchen worktop, 166cm by 295cm cut in sink and gas hob, under counter join please

We are replacing our gas hob with an electric induction hob. We need the old gas hob to be tapped off so the kitchen fitter can install the new induction hob.

Work required: 1. Fit and install my built-in electric oven into the oven housing unit, which I have already purchased. 2. Install the electric hob above the oven. 3. Connect both appliances safely to the existing electrical supply. 4. Close and neatly finish the gap between the two existing kitchen worktops. The gap was previously used to accommodate a freestanding cooker, and now needs to be filled to allow for the built-in oven and hob installation. 5. Ensure the worktop is properly finished and the hob fits securely. 6. Test all appliances after installation. Please note: * Oven, hob and oven housing unit have already been purchased. * No appliances or units need to be supplied

Kitchen Hob model Whirlpool General 2000+ model. Ignition switch is stuck.

To fit Hoover induction hob in to space on worktop. The circuit has already been checked.

I turned the oven on and the fuse box fused. I’ve left the fuse off after trying this twice. Not sure what to do

I'm looking to have this induction hob installed over my oven - it's going to be a replacement for the current one, so the old one needs to be removed prior to the installation: https://www.samsung.com/uk/cooking-appliances/ovens/nz8500bm-6-2-cooktop-flex-zone-plus-wi-fi-connectivity-smartthings-cooking-nz64b6056gk-u1/?srsltid=AfmBOoqGPZ4Atucp9ebkIsPUuUU2s8y3QeXdR49blWhXFlm34XgRdKO9&fbclid=IwZXh0bgNhZW0CMTEAAR21yL0EJMWuYNXy5lLN_zbfa5v2lsNbNsFutKqUmTHz0thVXLjBXmo9-9Q_aem_OsinUwFyW0kFFRbRSaFzVQ

Replace the old electric hob with the new hob

I need an induction hob fitted - the worktop needs to be cut slightly to fit it and the wires need to be connected. It would also be good for the crack between the tiles and worktop to be filled at the same time if possible

I need a hole cutting in a piece of worktop to fit a gas hob and a sink in another piece of. I then need the gas hob connecting to the gas line and the sink plumbed in , straight swap, old sink out and new sink in . Appreciate a joiner might not be able to connect the gas so wiling to get someone else to do that but if you can do it all even better

Remove old hob and replace with new one

We would like to replace our kitchen extractor fan above the hob as ours no longer works

Gas hob not working properly

We need an electrician to reinstall a Zanussi induction hob.

I’m looking for a qualified electrician to replace my existing hardwired ceramic hob with a new induction hob. Existing hob: Indesit RI 161 C ceramic hob (6.2 kW) New hob: Hisense Hi8 HI6443BSCWF 60cm induction hob (7.36 kW) The existing Indesit hob is hardwired into a dedicated cooker supply and will need to be safely disconnected and removed. The new Hisense Hi8 also needs to be hardwired, using the existing cooker circuit if it is suitable. Please check that the existing circuit, cable, protective device and isolation arrangement are appropriate for the new 7.36 kW induction hob before connection. The existing worktop cut-out should already be compatible (approximately 560 × 490 mm), so I am not expecting any worktop modification to be required. Scope: 1) Safely isolate and disconnect the existing hardwired Indesit hob 2) Remove the old hob from the worktop 3) Check suitability of the existing cooker circuit for the new 7.36 kW induction hob 4) Install and hardwire the Hisense Hi8 HI6443BSCWF 5) Secure the new hob correctly in the existing worktop aperture 6) Electrically test the installation and confirm safe operation 7) Dispose of the old hob as appropriate for electrical appliance if this is possible or alternatively, load into car for disposal at Raynesway Household Waste Recycling Centre, please let me know if disposal is included in your quote. Please quote for labour and any standard electrical connection materials required. If you anticipate that the existing circuit may require upgrading, please indicate how this would be assessed and any likely additional costs.

Fit a new kitchen worktop and a gas hob with built in oven

hob stopped working. Most likely fuse needs to be replaced.

Hi, I need a kitchen a worktop replaced with new worktop, cut to size and cut to fit cooker hob. If you can install the hob also that would be great