Find professional roof installation services near you

Install 3 x Yakima roof racks onto Rhino-Rack Backbone – Toyota Hilux I have a Rhino-Rack Backbone system already installed on my Toyota Hilux and need 3 x Yakima crossbars/racks fitted to it. I have all the Yakima racks and mounting hardware. I've attempted the install myself, but there isn't enough room for me to get my fingers/tools into the correct position to secure the mounts properly. It may be possible for someone with the right tools/experience to install them with the Backbone in place. Otherwise, the Rhino-Rack Backbone may need to be removed, the three Yakima racks assembled/mounted to it off the vehicle, and then the complete assembly reinstalled. Looking for someone experienced with Rhino-Rack/Yakima/4WD roof rack installation who can work out the easiest way to get it fitted securely. Budget: $200

I want a permanent transparent roof installed on my feature wall covering the entire wooden frame as shown in picture. SIZE 14 Ft long and 5.5 Ft. Wide See example pic of how I am expecting it to look like. Also see the actual area picture that needs roof.

Licensed electrician needed to prepare wall for a new access door into the roof space/void behind the third floor. See floor plan and photos attached. Work required: * Remove existing wall sconce. * Relocate existing two-gang light switch beside the new door opening. * Inspect and reroute electrical cabling currently running through the proposed door opening. * Relocate any electrical enclosure, junctions, transformers/power supplies or wiring that would obstruct the new door frame. * Supply and install a basic 1200 mm surface-mounted LED batten inside the roof space, using the existing lighting circuit if suitable. * Position the light switch conveniently beside or just inside the new access door. * Supply minor materials, test the work and provide the required electrical safety certificate. Current roof-space access is via a manhole on the middle floor using a ladder.

Need a ventilation fan installed on roof off trailer Fan attached below Needs transformer installed with it as it's 12v

Install roof racks on my Subaru forester, and install an awning I will have all the parts ready to go. Would be good if you have done this before or handy with this stuff

I need someone to bolt this roof top tent rack to my Hilux. Have the rack but no screws. It probably needs a rivet set up put into the tub so that it screws in properly.

Need roof rack and radio installed, roof rack is assembled and half of cars roof has been pulled free ready for installation

Hi there, I am looking for quote for installation of Zincalume/Colorbond roof. Property Type: Single storey residential Roof Type: Pitched Roof Approximate Roof Area/Size: 120m2 Location: Braybrook 3019 Notes: Current roof is cement sheet asbestos, which will be removed prior Please describe inclusions and exclusions. Thanks Alex

Hello, I need to have my Yakima Trim HD roofracks installed onto my Honda CRV 2017.

Sheeting to roof to cover 5 sky light panels

My kitchen rangehood is installed and working, but it is not ducted to the roof. Smoke and steam currently stay inside the cabinet. Tile roof Scope of Work Cut a hole in the cabinet shelf above the rangehood (no existing hole) Install 150mm aluminium ducting from the rangehood outlet up into the roof cavity Run ducting through the roof and install a proper roof cowl/vent (tile roof) Ensure correct flashing and waterproofing around roof penetration Secure all duct connections (no PVC — must be aluminium or semi‑rigid metal duct) Test airflow to confirm smoke is venting outside

Looking for someone experienced with installing roof racks and rear ladders on a Suzuki Jimny (5-door) to install mine in Wollstonecraft. Both the roof rack and ladder are already supplied — I just need someone with the right experience and tools to install them properly and carefully. 🚙 Vehicle: Suzuki Jimny 5-door 📍 Location: Wollstonecraft, NSW 🔧 Job: Install roof rack + rear ladder 🧰 Tools: Please bring all tools/equipment required ⚡ Important: The installation will need to be completed on the street with no access to a power supply. The street has 2-hour parking, so please take this into consideration. Experience is important to me. I really love my Jimny and want to make sure the installation is done correctly without damaging or scratching the vehicle. I’m therefore looking specifically for someone who has previous experience installing roof racks/ladders, ideally on a Jimny or similar 4WD. Photos for reference

Install imbedded roof rack for GWM tank 300. Urgently needed - should take no longer than 30-45 mins to complete Must provide own tools. Installation guide here: https://youtu.be/qzMRVJi6to8?si=PUCwpQJ6zEXO33V3

Need a roof tiler to supply and install missing roof tile as pictured. Flexible with the dates and located in Sunbury. Open to reasonable offers.

Require TV Roof Antenna installation on roof and connection to existing Tv cable box at side of garage to provide terrestrial TV reception for Televisions in house

Assemble and install ozroo tub rack on 2020 Ford Ranger Wildtrak. Also mount rooftop tent onto rack. All parts supplied. Looking for someone with experience fitting roof racks, tub racks or rooftop tents. Morningside area

We are looking for someone to install a floor-to-ceiling mount at a pharmacy in Clayton, Victoria. Once the pole is installed, mount 2 TVs to the pole and commission them. The floor-to-ceiling pole is 5030mm in height. Please ensure you are ok with working at heights. The TV's are mounted at eye level. I do not have any photos to share, but I will have these in the next day or so once the we have finished the shoppfitting. Everything is on site ready to install.

Need the new installation of one roof sheet. I will pay for the cost of materials. Need done today if possible.

Install 3 bossco roof racks to van. ( need to be drilled)

Looking for a qualified, licensed electrician to install 7 ceiling light fittings in a residential property (Campsie). Scope of work: Remove existing ceiling lights (standard batten fittings currently installed) Install 7 new light fixtures (mix of glass batten fix shades + pendant-style fitting) Ensure all wiring is safe, compliant, and properly secured Test all lights post-installation Details: All light fittings are already purchased and on-site Locations include: bedrooms, living room, kitchen, and staircase/landing area (high ceiling) Stairwell light is positioned at height – requires appropriate ladder or access equipment Photos attached for reference of current fittings and new lights Requirements: Must be a licensed electrician (NSW) Must provide certificate of compliance (if required) Must bring suitable ladder/access equipment for high ceiling/stairwell Own tools and equipment Experience installing similar fixtures (especially pendants) Timing: Flexible, but looking to get this done ASAP