Find professional roof installation services in NSW

Recently picked up a pair of second hand Mazda genuine roof racks. Just need them installed.

Professional installation of a polycarbonate roof for outdoor pergola. Will need 2 people. Requires removing existing roofing, removing some existing wooden beams, fitting and waterproofing new polycarbonate sheets (sheets supplied), installing blinds (supplied), making good whole area. Will need to remove and dispose of waste. Full detailed instructions will be provided

Remove existing roof downpipe Purchase new roof downpipe Install new roof downpipe

I’m looking for a licensed electrician (NSW licence required) to install a small rooftop ADS-B antenna at my home in Blakehurst and earth it properly. The job: Mount a fibreglass or PVC mast, 1–1.5 m, on a gable end or fascia. It must go on a roof face without solar panels and stay at least 1–2 m from the panels and DC cabling. No fixings into the solar rails. Run the supplied 10 m coax cable from the antenna into the house, weatherproofed with a drip loop. Install a DC-pass N-type coax surge arrestor where the cable enters the house. Earth the arrestor with a short 6 mm² green/yellow lead to the main earth at the meter box. If the entry point is too far from the meter box, drive a new earth stake and bond it to the main earth per AS/NZS 3000. Do not bond anything to the solar array frame earth. Provide a Certificate of Compliance for the earthing work. I’ll supply the antenna, the 10 m coax cable and the receiver. Please say in your offer whether you’ll supply the mast, bracket and arrestor, or want me to buy them. Timing: Flexible, weekday or Saturday.

Need to get and install new gutters/downpipes within my budget for a one storey, two bedroom house in Blacktown. Old gutters already removed. Has 5 corners roughly 30m in length of gutter required. 3-4 down pipes and 1 was removed.

Need to install our StarLink on the roof of our house. Balcony access to roof.

Looking for someone experienced with installing roof racks and rear ladders on a Suzuki Jimny (5-door) to install mine in Wollstonecraft. Both the roof rack and ladder are already supplied — I just need someone with the right experience and tools to install them properly and carefully. 🚙 Vehicle: Suzuki Jimny 5-door 📍 Location: Wollstonecraft, NSW 🔧 Job: Install roof rack + rear ladder 🧰 Tools: Please bring all tools/equipment required ⚡ Important: The installation will need to be completed on the street with no access to a power supply. The street has 2-hour parking, so please take this into consideration. Experience is important to me. I really love my Jimny and want to make sure the installation is done correctly without damaging or scratching the vehicle. I’m therefore looking specifically for someone who has previous experience installing roof racks/ladders, ideally on a Jimny or similar 4WD. Photos for reference

Seeking an experienced installer to mount a flat (non-corrugated) polycarbonate patio awning onto an existing timber frame structure. The awning measures approximately 4.2 metres wide by 3 metres deep. Preference for durable, high-quality flat polycarbonate sheeting suitable for long-term outdoor use.

I need somebody who’s capable to install 3 eave/soffit vents along the North and West roof cavity walls as air intakes. Needed as we intend on installing a solar exhaust fan later on. Details: • Roof cavity accessible via manhole in primary bedroom; • House is a two-storey brick veneer with cement/terracotta tiles;

Install imbedded roof rack for GWM tank 300. Urgently needed - should take no longer than 30-45 mins to complete Must provide own tools. Installation guide here: https://youtu.be/qzMRVJi6to8?si=PUCwpQJ6zEXO33V3

Help cut & install roof vent – Hyundai Staria Load Looking for someone experienced with van conversions, automotive bodywork or similar to help me cut and install a Fiamma Turbo Vent Premium into my Hyundai Staria Load Premium. I already have the vent, installation products and tools, including a jigsaw — I’m mainly looking for someone who has done this before and is confident accurately measuring and cutting into a vehicle roof. I’ll be there to assist and can do the prep/finishing work myself. Ideally looking for help with: • Confirming the best position and measurements • Marking and cutting the roof opening • Deburring/treating the cut metal edges • Helping fit and weather-seal the vent if time allows I have all tools and materials required. 📍 Artarmon or Rouse Hill 📅 Ideally Friday 14 August Please let me know if you’ve installed roof vents/windows or done similar vehicle bodywork before.

Require TV Roof Antenna installation on roof and connection to existing Tv cable box at side of garage to provide terrestrial TV reception for Televisions in house

Install roofracks on car

Install a powered roof ventilator including power connector in roof (such as an airomatic) and a TV aerial.

We want a simple roof put in over our outside patio in colourbond or perspects. It can be simple as we would pull it down in the future when selling.

To install transparent roof around 3.2m*2m with suitable support to make around 2.8 m height

Remove existing, supply and install roof gutter. Single storey building and a garage. Around 100 linear meter and 8 corners.

Need Roof sheeting installed inside existing shed to stop condensation dripping on to stored goods

Need to replace/install 4 polycarbonate roof sheets. No measurements have been done yet. Sheets are still unavailable as well. Open for recommendations. Thank you.

Install 3 bossco roof racks to van. ( need to be drilled)