Find a professional Laserlite contractor near you

I have a large odd shaped pergola attached to the back of my house that needs the Laserlite Twin Wall Polycarbonate roof sheets (10mm) replaced due to hail damage. The current width of the sheets are 1220mm, with one sheet length nearly 7m long.

Remove mesh. Supply and install laserlite on fascia of patio. 2 x 11mx1m runs. Can do with 4 x 6m lengths of clear laserlite. Can be screwed direct to fascia. Looking to reduce rain ingress, but doesn’t have to be “waterproof”

Laserlite sheeting has never been fixed, just wedged into place allowing debris to enter shed.

Approximate pergola measurements are 4.22 metres X 4.5 metres. I can source roofing material. Looking at labour cost only

I need the old roofing taken off and new panels installed and extended right across

Replace laserlite over deck,approximate area 800 x 300.

Needing 30 x1800mm polycarbonate sheets installed on roof. Sheets provided by me.

Need someone who had experience replacing laserlite roof. Original one is old and brittle. New roof sheets already on site. Just need to trim it down. Need to remove flashings and replaced carefully afterwards. Price is just indicative, please quote accordingly.

Outdoor patio roof needs new laserlite

I need help to remove some corrugated laserliite sheeting that's come loose and assist with a solution to patch the covering over my back porch.

UPDATE: I need the fence work to start this weekend. Description: I’m looking for help with a few jobs around the house. To begin with, I need the following done: 1. Build a picket fence: 10.5 metres (6 posts), 65mm width x 900mm height with 25mm gaps 2. Build a paling fence: 5 metres (3 posts), 100mm width x 1m height, no overlap 3. Replace Laserlite sheets: 16 sqm approx. I’ll need someone with a ute to help pick up materials from Bunnings. There are a few additional tasks as well, but I can’t fully gauge the scope at this stage, so an hourly rate would likely work best. Timing: Fence work needs to start this weekend; the rest is flexible. You need to have a ute to help me purchase and bring supplies from Bunnings tomorrow morning or weekend. Please state if you can start this weekend and also your hourly rate. Thank you heaps.

I’m looking for help with a few jobs around the house. To begin with, I need the following done: 1. Build a picket fence: 10.5 metres (6 posts), 65mm width x 900mm height with 25mm gaps 2. Build a paling fence: 5 metres (3 posts), 100mm width x 1m height, no overlap 3. Replace Laserlite sheets: 16 sqm approx. I’ll need someone with a ute to help pick up materials from Bunnings. There are a few additional tasks as well, but I can’t fully gauge the scope at this stage, so an hourly rate would likely work best....or give me a quote for each or all together please. I will assess and go with what works best. Timing: Fence work needed ASAP; the rest is flexible.

Laserlite sheets on pergola need changing

Need laser lite replaced with a colour bond to stop leaking

Full replacement of 4m x 2m deck- joists and decking boards. Leaning towards spotted gum for boards. Removal of old deck. There’s a split system fan unit sitting on the current deck that will need to be moved/suspended, perhaps disconnected to enable works. Also, a simple roof of the same size to be replaced, above the deck. Colorbond or Laserlite sort of deal, roof is pretty high up so might require scissor lift and harness setups for safety reasons so high up!

Three small lasterlite panels deck roof to be replaced due to hail damage. I have a full sheet of the materials which should cover the job

Need someone to put a roof on my pergola. Thinking laserlite will work well. 4500 x 3300 in size.

Looking for someone to replace the laserlite alighted with the 3 windows out the back to let in light into the house. Approx 6-8 sheets need to be replaced

Need to supply and install Laserlite (Platinum grade) shade for my inverter and battery. Able to have acces for future servicing.

Replace laserlite roofing some panels damaged from branch drop and hail. 15 panels approx measurement is: one section 4.2 and another is 3.6, hence why a site visit is needed for quotation purposes. Pls note the budget estimate is based on what I think the materials only would/could cost…..?