Find experienced local roofers in Sutherland Shire

Replacing approx. 10 pop rivets with Hex Flange Metal Top Grip Roofing Screws to re-fix awning's metal capping. We have screws.

I’m looking for a roofer to install a roof cowl that will vent steam from an existing duct. The duct is already set up and ready, and the hole is already cut into the sarking. The only task required is installing the cowl itself. I’ve already purchased the cowl. You just have to install it.

Looking for an experienced tiler/waterproofer to complete laundry works. Scope of works: • Fix the fall in the shower area to correctly fall to the drain and also ensure laundry fall will work. • Waterproofing • Tile the floor 6m ² • Tile walls approx 9m ² • Tiles and Epoxy grout supplied All tiling is direct stick no screed bed

- Repoint of all ridge capping - Change broken tiles (last checked a few months ago and none were broken) - Check roof valley for small leakage in the ceiling (could be just the direction of the wind when it rains) Two story house.

Some water damage in the roof, leaked has been fixed just need to ceiling restored

Roof Sheeting Replacement to Rear Roof Removal of 2 air conditioning units To be degassed and reinstalled Remove satellite dish Remove the corrugated roof sheeting and flashings to rear roof New batons to be installed 50mm foil backed insulation Clip lock roof sheeting Flashing to 2 walls Barge capping to one side Reinstall air con units. Main Roof Remove roof tiles to back side where no sarking Remove tiles to flashing area at the front Remove incorrectly installed flashing Replace with new tiled flashing New sarking to underside of roof tiles Reinstall batons Reinstall roof tiles Replace approx. 2—25 broken roof tiles Repoint ridge caps and barges

Provide gutter cleaning on 2 sides of a duplex and install gutter guards across each gutters (2 storey house)

Prepare van roof for respray

replace antenna on my single storey roof (new antenna on-site already). Mast is in full working order, no adjustment required. Please bring ladder and tools. Can be done any day.

2 storey house. I need leaves removed from 3 gutters (all with leaf guard installed) and 2 valleys

Fix boarding on roof that fell off

I need a quote to clean 30 solar panels on a single story tin roof Need to use afterpay

I need my gutters cleared of a few leaves ABs twigs and guard reinstalled in a few places

Attach 3 bracket to two downpipes. Have brackets.

Clean up roof and gutter guards of leaves and debris. Note there are two levels requiring attention.

Roof of living room of 2 bedroom unit needs to be sanded back, and repainted. You will need to bring own tools and paint.

I’m looking for someone experienced with roof racks / platforms to finish installing and correctly align a roof rack platform on my vehicle. Vehicle: 2024 Mitsubishi Outlander Exceed Equipment: Rola Ridge Mount rail system (TKRM315874 – installed) Rola roof platform/tray (assembled but not mounted) The Ridge rails are already installed correctly on the vehicle. The issue is that the platform mounting plates are not aligning with the Ridge rails — front and rear spacing doesn’t match, so the tray won’t sit down and bolt on correctly. The platform itself is square (diagonal measurements match), so I believe this is a mounting plate orientation / positioning issue, not faulty parts. What I need done; Inspect current setup Correctly orient and position the platform mounting plates Align the platform to the Ridge rails Secure and torque everything correctly Confirm fitment is safe and correct There’s been some confusion on my end during install and I’d prefer someone who: Has installed roof racks/platforms before Understands rail-mount vs crossbar-mount systems Can quickly identify incorrect plate orientation or slot placement All parts are present, this is not a fabrication job, just correct fitment and install.

I need to hire someone to clean the gutters for my 3-bedroom house. Thank you

Hi there, I am looking to get a quote for gutter cleaning for the perimeter of one side of double storey duplex. See attached photo. At this point, I don’t know how much it should cost.

Fairly self-explanatory just someone to cut and put a roof vent already purchased from Bunnings on the roof as well as cut a hole in the corrugated iron and install a window 79x80