Find trusted mechanics in Melbourne

Assembly of a portable ro system purchased online. It's very simple but Did not come with instructions so just want someone that knows to handle it

Looking to install the below unit. The car model is 2010 Subaru forester https://www.ebay.com.au/itm/376308094390?chn=ps&_ul=AU&_trkparms=ispr%3D1&amdata=enc%3A1UZQ4lUPbT8euHUvknI9XaQ36&norover=1&mkevt=1&mkrid=705-173151-935305-0&mkcid=2&mkscid=101&itemid=376308094390&targetid=2370046502538&device=m&mktype=pla_with_promotion&googleloc=9112820&poi=&campaignid=21766134162&mkgroupid=175112620264&rlsatarget=pla-2370046502538&abcId=10047381&merchantid=5375545398&gad_source=1&gad_campaignid=21766134162&gbraid=0AAAAAD97CxREMH8f8m9h0SlD7JY55DuMN&gclid=CjwKCAjwtIfPBhAzEiwAv9RTJoDGUgd4ixYz8syLc8k5QsgYpC1xRBVsR2g01ndOs6rEaXHKuS4wBRoCCHMQAvD_BwE

Hi have a new Warn XD9 winch to install onto existing bullbar to my 1985 Landrover 110 County. Battery is located under passenger seat so power cable will need to be extended.

Need experienced mechanic service 2 cars – must follow exact oil change method. Oil and filters Supplied Description: Looking for someone to do an oil and filter service on 2 cars. This is not just a normal quick oil change. I want the job done exactly to a specific method step by step, so I need someone who is careful, patient, mechanically minded, and happy to follow instructions properly. Please only apply if you’re confident doing the below exactly as requested: Required oil change procedure: 1. Start with the engine completely cold. 2. Add about 1 litre / 1 quart of fresh oil to the existing oil as a pre-flush. 3. Start engine and let it idle for exactly 5 minutes. 4. Turn engine off and wait 10 minutes. 5. Then drive the car 10–15 minutes to full operating temperature. 6. Park on level ground, let it idle 2 more minutes, then drain the oil immediately while hot. 7. After the first drain, leave it for 30 minutes, then remove the drain plug again and do a second drain. 8. Fit new oil filter, but pre-fill the filter to about 60–70% with fresh oil first. 9. Apply a thin film of oil to the rubber gasket and hand tighten only. 10. Refill engine slowly with about 80% of oil capacity first. 11. Wait 5 minutes, then top up slowly in small amounts, checking the dipstick each time. 12. Final oil level should be around halfway between low and full, not overfilled. 13. After refilling, do not start the engine straight away. 14. Turn ignition on without starting, wait 10 seconds, then turn it off. 15. Repeat that 3 times. 16. Then start engine and let it idle for exactly 3 minutes without touching the accelerator. 17. Check for oil leaks around drain plug and filter. 18. Turn engine off, wait 2 minutes, then re-check oil level and top up if needed. Must Have • has experience servicing cars, or is very mechanically capable • has their own tools • works cleanly and carefully • is happy to follow this exact process, not their usual rushed method

I need an aeroflow 72-4010 trans cooler with aeroflow 72-4000 bracket installed to my grand Vitara. It has a nudge bar so hardest part would probably be removal of nudge bar and bumper and installing cooler in optimal position in front of radiator.

Car oil change of Volkswagen Golf

Looking to get an oil change for my Mazda 3 sedan, I live on a main road in st kilda but if you require a private space I am able to organise space in the garage. The car is also low on quite a lot of fluids so if you’re able to provide those additional services I’m more than happy to negotiate with price. Thank you in advance.

Hi, I’m looking for someone experienced with basic car mechanical work to help with a few jobs: Replace fan belt on my Mazda 3 2010 (automatic) – I already have the replacement belt. Do a transmission service – I’ve got the transmission oil ready. Swap hubcaps on another vehicle – just a straightforward hubcap replacement, all parts supplied. I’ll provide all the supplies (fan belt, transmission oil, and hubcaps). You’ll just need your own tools. Prefer someone who’s done similar work before or is mechanically experienced. Location: Ascot Vale, Melbourne Timing: Mondays and Thursdays & Weekends

I need someone can do fitting bullbar brand Hammer to my car prado 2019.

I’ve tried to replace the oil cooler on my ford fiesta 2010 1.4tdci. I’ve got the parts and have done 90% of the job but can’t get the oil cooler to come off the stud to swap it out.

Needing timing belt and water pump replaced for a 2006 hyundai getz hatchback. Also need a service as I'm travelling up to Sydney April 18th. Can supply registration for cost. Would like a reputable and licenced mechanic!

Change car oil in jeep compass

It’s time to service the timing belt on my CRAFTER 2016. Done 100k km. Not in a rush. Flexible in time. Timing belt + water pump. No parts supplied. Expect warranty included.

Toyota echo 2004 Upgrading my old head unit with the new head unit i bought recently Plus reverse camera

clutch replacement on a 2006 mini cooper

Just regas of a 2014 Holden Commodore. Flexible with times, preferably over the next 5 days. Onsite or st kilda area

Need an oil and oil filter change. I can supply oil and filter.

AC needs regassing as accidentally unscrewed it and broke the O-ring

The car is shaking when I try to accelerate and needs spark plug and ignition coil (quantity unknown) replacement.

I have an 80 series Toyota Landcruiser. I have purchased a double din Sony head unit and the required accessories for it to be fitted to replace the original head unit. I need someone who is familiar/experienced with replacing head units in cars.