Find local air source heat pump installation & repair near you

Replace existing 350L outdoor electric hot water system (postcode 2223).Upgrade to a 270–315L heat pump system. Please provide a quote for supply and installation, including ESS and STC rebates.Prefer a like-for-like replacement in the same location.

The heat pump dryer is turning on but not spinning after a wet heavy load was attempted to dry.

Concrete slab for new electrical heat pump to sit on. 700 x 700, it’s on a slope and concrete underneath slightly cracked.

I have a dryer that apparently needs new seals. It is partly disassembled (just the covers). If you repair these dryers contact me. I will pay for parts. No hurry.

My Hisense heat pump dryer has stopped spinning. Will turn on, no error code but drum wont spin. 4 years old.

We have a water heat pump system at the back of the shop. The outdoor unit with fan and compressor is attached on the wall, but needs to be moved 30cm on the right as it is overlapping on the neighbour so part of the wall. Please note the unit has refrigerant gas lines that would need déconnexion.

Service hot water heat pump

I'm looking to replace my current gas water heater with an electric heat pump. That will also mean needing some electrical work done. And finally, I'll need to have my old water heater removed.

Bosch serie 4 heat pump dryer is not drying clothes fully. May require servicing due to lint on condenser and excess water from clothes not filling tank as before

Haier 8kg Heat pump dryer is getting very hot after drying a load- filter and condenser filter cleaned often and still have issue. Is there any way to resolve this?

Heat pump dryer not collecting water or drying clothes - turns on and runs the whole cycle

My Emerald Energy heat pump hot water system is playing up. Two issues: 1. The pipe running to the gutter (TPR discharge pipe) is releasing a large amount of water constantly 2. We’re only getting lukewarm water — not hot

I’m having an issue with my Bosch heat pump dryer—it’s not working. The store advised that the motherboard needs to be replaced as it was damaged by pests. If anyone can help with repairs, please contact me. Thanks.

We need a Britec adjustable dryer stand assembled (easy) and need our 50kg heat pump dryer (heavy) placed on top. It is going in a tight space but I’ve measured everything so it’ll fit perfectly.

need the pool heat pump connected. What’s already in place: • 32A breaker in the switchboard dedicated to the heat pump • 6mm cable already run from the breaker to the isolation switch • Isolation switch installed next to the pool equipment • Heat pump is in position Scope of work: • Open the isolation switch and confirm the 6mm feed is correctly terminated • Run the final connection from the isolation switch into the heat pump • Test the circuit to make sure it’s drawing correctly on the 32A breaker

Change out PCB boards on hitachi heat pump (I have ordered). Work through boards to see which is faulty and replace. (I get a refund for unused/unopened boards

Bosch Serie 4 dryer WTH85200AU - runs but very inefficiently. Clothes take forever to dry on all settings. Need someone to see what is wrong with it.

I’m looking for a licensed electrician to install an outdoor weatherproof power point for a new heat pump. Scope of work: • Install 1 x outdoor weatherproof GPO (power point) on the external wall in the location I’ll show you. • Existing internal power point directly behind the desired location, and • Another existing power point approx. 10 metres away on the same wall outside. • Power board is 15 meters from the desired spot. Preferably a dedicated/isolated 15A power run via conduit from power board, which is approximately 15 meters away. • Outdoor power point unit will be supplied by you. • You to supply all other materials: cable, conduit/trunking, fixings, etc. • Test the circuit, ensure it’s RCD‑protected, and provide any required certificate of electrical safety/compliance. Requirements: • Must be a licensed electrician (please include licence number in your offer). • Experience with external/weatherproof power points. • Clean, tidy work and must make good any small penetrations made. Timing: • Flexible on day and time – ideally within the next 1–2 weeks. Please let me know: • Your approximate total price (labour + materials, excluding the power point itself), and • When you’re available.

my dryer keeps showing an error message saying “the water tank is full, please empty and continue the cycle.” But the hose is connected straight to the sink drain, so it should be draining automatically. It seems like either water might be coming back up the hose, making the dryer think the tank is full, or the hose itself might be blocked. If someone could check it out, I’d really appreciate it. No rush..

Ecogenica model Eg-215f, Failed capacitor or tripped safety switch issue. 15mm tempering valve has been replaced same issue. Recall for where the control panel inside the heat pump unit hasn't been touched just out of warranty 2yrs & 3 months now. Warranty 2 yrs. Need quote on repairs. Thanks in advance. Not a emergency situation.