Find an experienced handyman in Springvale VIC

-fix door handle -fix door motion( it doesn’t run smoothly)

We are in the process of moving to a new house and I need handyman support to unscrew the brackets and remove curtain rods and install them in the new home. Will also need help with taking out a few photo canvases from the walls of the current home. Both the homes are in Springvale and about 10 min drive from each other.

2 holes in drywall approximately 20x20cm to be patched up + undercoat at minimum. Pls quote.

I would like to replace the door knob and the broken tile next to the door.

The frameless glass shower door in my bathroom has come off its rotating/pivot hinge and is currently not functioning properly. From inspecting it, the existing hinge/hardware also appears to have been a temporary or previous repair, so I don't just want the door reattached — I would like the hinge and mounting hardware properly inspected and repaired/replaced as required. What I need: -Inspect the existing shower door and pivot/rotating hinge -Safely refit the glass door -Check whether the existing hinge/hardware is suitable and secure -Replace the hinge/hardware if the existing setup is damaged, loose or a temporary fix -Ensure the door opens/closes correctly and is safely supported -Supply/install any replacement hardware required The door is a frameless glass shower door, so experience working with shower glass/frameless shower doors is preferred. Please include your labour cost and advise if replacement hardware/materials would be additional. Photos attached.

Looking for a plumber to inspect and repair the wastewater pump system under the kitchen sink. The pump was working normally last night but has now completely stopped. The guest has already tried switching the power off/on and resetting it, but the pump is still not running or making any sound. Please diagnose the issue and repair the pump if possible, or advise if replacement is required. Please bring the necessary tools and let us know your availability and estimated cost.

Looking for an experienced window repairer to quote on restoration of one awning (push-out) aluminum frame window at my home. Please supply all parts. What needs doing: Fly screen mesh has come away from the frame at the bottom-right corner and is torn. Re-mesh or replace the screen, fitted properly and cleaned up. Screen/window frame – aluminium frame needs checking, cleaning and any loose or damaged sections fixed so the screen sits flush. Winder – the window winder/handle at the base needs inspecting and repairing or replacing so the window opens and closes smoothly. How I'd like to run it: Stage 1 – $50 for an on-site inspection and a quote for the full restoration, including all parts and labour. Stage 2 – if I proceed with your quote, the $50 is credited towards the total price. Availability: I work from home, so weekdays are easiest for both the inspection and the repair. Flexible on time of day. Photo attached. Happy to answer questions.

Fixing fly screens and clean up

I need the broken sidelight panel beside my front door replaced. I am open to either: - Suitable obscure or patterned safety glass, or - A 6 mm hard-coated, UV-stabilised frosted polycarbonate panel such as Lexan, Makrolon or equivalent An exact match to the existing decorative glass pattern is not required. My priorities are security, durability, privacy, weather resistance and low maintenance. The successful Airtasker will: - Inspect the existing frame and confirm the required measurements - Supply the replacement panel - Carefully remove and dispose of the damaged glass - Install the new panel into the existing timber frame - Minimise damage to the existing timberwork - Ensure the installation is secure and weatherproof - Confirm the proposed material is suitable for an external front entrance - Confirm compliance with applicable Australian safety requirements Approximate dimensions: - Height: 2000–2070 mm - Width: 450–500 mm - Existing hole in the glass: approximately 190 × 60 mm - The entire panel requires replacement These measurements were taken using the iPhone Measure app and are approximate only. The successful Airtasker must verify all measurements on site before ordering or cutting the replacement panel. Please include in your offer: - Total supplied and installed price - Recommended material and reason - Product or brand proposed - Panel thickness - Whether removal and disposal are included - Earliest availability - Warranty on materials and workmanship Location: Springvale VIC Photos and an approximate measurement diagram are attached.

Need a door hung and one fixed as it is out of plumb. Also need one part of door jam replaced. I have all the material I just need someone with tools/drill etc

I need an experienced plasterer or carpenter to permanently close and finish a former wall-heater recess. The recess is approximately: - 1.95 metres high - 45-47 centimetres wide - Existing small opening approximately 29 x 26 centimetres Work required: - Inspect the cavity and existing framing - Remove loose or damaged material - Add timber framing or battens where required - Install plasterboard flush with the surrounding wall - Set joints and sand smooth - Replace the missing section of skirting board - Prime and paint the repaired area to closely match the existing wall - Supply all materials - Remove rubbish and leave the area clean The finished surface should look like a normal internal wall. Please provide an all-inclusive quote and confirm your experience repairing former heater, air-conditioner or similar wall recesses. The old heater has already been removed. Any concealed gas or electrical connection must not be altered unless the Airtasker is appropriately licensed. I'm generally available at home during the week.

Nedd to fix a wall patch

One big and one small patch on the walls that needed to be fixed.

My kitchen sink tap has become loose and wobbles when I use it. I believe the retaining screw/nut underneath the sink needs to be tightened. I don’t have the tools to do the job myself, and I’m not sure if the sink or part of the plumbing needs to be moved to access the fixing underneath. I’m looking for someone experienced with plumbing or handyman work who has the appropriate tools to inspect and tighten the tap securely. Task includes: * Inspect the loose kitchen tap. * Tighten the retaining screw/nut underneath the sink. * Bring any tools required for the job. * Advise if any additional repairs are needed if tightening alone won’t fix it. Please let me know if you’ve done similar jobs before. Photos are attached for reference.

Mount a wall clock, weight 6.5kg, on a plaster wall in the living room.

Fix and tighten the parts in picture on the brick wall, use your own tool.

We have 2 toilets seats that have become unanchored to the toilet - the photo's attached show lack of bolts on both seats - allowing the whole seat to detach from the main bowl

Used a plunger, drano, pulled all the pipes out directly underneath the sink and nothing was blocked.

External roller shutter/blind appears jammed or misaligned. Currently stuck partially open. Looking for someone experienced with roller shutters/blinds to inspect and repair. See attached photo.

I need to put curtain rods on the ceiling to hang see through curtain for all the windows at my house. The curtain rods are bought from ikea