Find a professional mdf contractor in NSW

Need to trim 2 x MDF kitchen cabinet door, one cut on each. - Due date: Flexible

Cut MDF board (3) to reduce size. See image.

We need the MDF VJ panels installed on one wall in our house (Emerald Hills, Leppington). Sitting wall - width 2.62m - height 2.4m - light switch, power boards, tv point etc.. total 7 points Panels (provided) - 2400x1200x9mm - We have 3 panels from bunnings. - May need cut in length as it seems they are 2.42m in height - Due date: Before Saturday, 19 November 2022

Rendered brick walls 3.4m (W) x 2.4m (H) Bedroom Wall 1 - no doors 2.7m (W) x 2.4m (H) Bedroom Wall 2 - one doorframe 8.0m (W) x 2.4m (H) Hallway wall - two doorframes - Due date: Before Friday, 25 November 2022

Cut MDF board to reduce size. - Due date: Flexible

Install wood into top part of cupboard. - Due date: Before Sunday, 30 October 2022

Install MDF panels on a gyprock wall that is 3.70mts length X 2.70mts height (incl cornice and skirt board ). The brand of the panels is easycraft and they can be clicked together. Panels are 1.2mts long for 3.0 mts height. Need to allow for two power points (open holes on the panel). Pls include cost of glue and nails in your quote. See below product description and video on how to install. I have attached a photo of the space and a sample photo of how the product looks like once installed. https://www.easycraft.com.au/products/easygroove/ https://m.youtube.com/watch?v=7tcO8yYM0zg - Due date: Flexible

Please see photo of cut lines by zooming in. I need you take this mdf sheet https://www.bunnings.com.au/900-x-1200mm-12mm-lining-panel-white-mdf-primed-demi-round-20mm_p0281895?region_id=117316&gbraid=0AAAAADtbEB934kxKOqZnnOab-aO6EpDPp&gbraid=0AAAAADtbEB934kxKOqZnnOab-aO6EpDPp&gclid=EAIaIQobChMI56q11P3j-gIVKJhmAh3LeAi8EAQYBiABEgKXg_D_BwE&gclsrc=aw.ds Either cut from van or I can drop to your place and pick up. Must be local to eastern suburbs. - Due date: Flexible

False wheel to be installed against an internal wire cage in a storeroom - Due date: Flexible

I need a good joiner/plasterer/carpenter with experience in MDF installation on plaster board/gyprock. Must be able to measure accurately and know how to install ( Glue vs Nails) on existing wall,( Gyprock). The contractor must have proper tools to cut and install. The designer panels need to be aligned properly so that design flow is proper ( not broken) There are 3 walls and 12MDF panels ( 2400*1200) to be installed - Due date: Flexible

Hi Firstly, I would like someone to buy 2x 2440 x 1220mm 3mm MDF Panel Standard from Bunnings. Link is below. https://www.bunnings.com.au/2440-x-1220mm-3mm-mdf-panel-standard_p0590021 Secondly, i would like you to install the panels to cover an arch opening so that the front room cannot be seen and is not accessible. Please include cost of the panels in your price (2 x $15.40 = $30.80) I've attached a photo of the arch which is 1.82x2.33m - Due date: Before Friday, 6 May 2022

Looking for someone who can install MDF finishing plasterboards on the wall and a small portion of the ceiling. MDF Boards have already been purchased so only labor is needed.

Install Sycon Axon VJ Board in bathroom - Due date: Needs to be done on Friday, 12th Nov 2021

Cut 16 MDF pieces and making 1mm deep grooves in a 45 degree angle.

Open end of carcass will sit on floor and needs to be mounted to bathroom wall, (rendered brick) without making carcass much deeper than it already is.

I have a timber bespoke bedhead and I need it to be covered in mdf wall panelling. Measurements are 2m wide, 1150cm high and 20cms deep. I have just included a photo of the product from Bunnings that we want.

4 parallel cuts on 3 sheets of 3cm MDF and wood particle board. Has been marked on boards. 3x 3m cuts along the length of 2 boards 1x 1m cut across the end of 1 board Needs to be this Wednesday 14th April between 9am - 3pm at Salisbury Rd Stanmore NSW. Power 240v available on site. Job can be done in adjacent laneway. I can help lift boards. You need to be experienced in this type of task, have a medium / large circular saw and have your own stands to put boards on while they are being cut.

I need pieces of MDF cut to specified size. I have plans for 2 small speaker cabinets for my desk. I’ve attached a screenshot of the overall design. I will provide the full detailed design if you’re interested. This should be a quick job with nearly all straight cuts. There are 2 circles that need to be cut out of each cabinet for the speakers. You will need your own tools as I don’t have the ones necessary. I’m happy to pay extra if you can also assemble the pieces together.

Hello, Needing to build and install a white MDF cabinet door and a cover over the exhaust fan in the kitchen. See photos for further reference. Thanks

Chipped cupboard if possible to look like new