Find an experienced handyman in Killarney Heights

Need plumber to come reinstall or rectify a leaking sink tap mixer now. At Killarney heights 2087

Hi, need someone to install headunit + digital instrument cluster for me on a Land Rover Discovery 3, looking for experienced installer. I have instructions for both on how to install the units. I also have a 360 cam in need of installation here with drill piece included.

Handyman to swap door swing from left to right and swap over the lock. Photos below. I have already taken the door off the hinges.

Install custom blinds that have been made in China and sent here to fit my OUTMOS (4m x 3m). Wiring can be done by my electrician, so just need a handyman. Heavy so will need strength or help from another person. All four sides have a blind, so it’s four blinds to install. $250per blind install for larger one, $200 per blind for smaller one https://v.youku.com/v_show/id_XNTkwNzk5NDA5Mg==.html

Hang several pictures, resize a picture board (maybe suit carpenter), small repair jobs around the house eg replace towel rack in bathroom

I need 2 new roller blinds and 2 sheer curtains installed

Hi there, We’re looking for someone with experience working on combustion heaters. The hinge on our heater door needs to be welded back on (may need some scrap metal or a bracket to reinforce) and we may also need a new door seal fitted. Ideally, we’d like someone who has experience restoring or repairing combustion heaters and can assess what else may be required to get it back into good working condition. Please get in touch if you’re able to help. Thanks in advance!

I need to bathrooms sheeted ASAP. Photos included. Each bathroom is approximately 2.4 x 2 m floors walls and ceiling

This task is to build a assemble a Stratco Handi-Pod (HP1) shed to the manufacturer's installation instructions, on an existing concrete slab. The shed will need to be anchored into the slab, so will require the use of your own masonry drill. The shed should also be sealed with silicone (or similar)around the base to prevent water ingress. The shed is new and onsite ready to assemble. Tools noted in installation guide as required: • Rivet Gun • Caulking Gun & Silicone • Cordless Drill • Hammer Drill (if Cordless Drill has no Hammer function) • 5/16 Hex-head & PH2 Phillips-head Bit (Supplied in Kit) • 10mm Masonry Drill Bit • 3.5mm Drill Bit (Supplied in Kit) • Ladder, Tape Measure Shed link: https://www.stratco.com.au/au/sheds--garages/garden-sheds/handi-pod-sheds/handi-pod-hinged-door-garden-shed-hp-1-slate-grey-hpgs21701410sg/ Shed install instructions link: https://www.stratco.com.au/siteassets/pdfs/handi-pod-garden-shed---hp1---install-guide.pdf

We need a slab laid for a garden shed. Shed is 2170mm x 1410mm and slab needs to be 100-200mm larger in each direction. Slab must be rebated to suit the shed dimensions. The site is sloped but I will level it for you. See area marked in red in first photo for shed location. I have plenty of 20-30mm aggregate if you wish to use that for the base. We have other concreting works which we need done we can be discussed.

Need assistance with a few handy jobs around the house including: - Hanging picture rails - Remove old dryer & lift new one into place - Tip run with old cupboard, rug, etc & green waste

Need a pool door latch fixing and also gate latch fixing so they auto close

Putting together a flat pack small garden shed.

Hi, I need 3 x roller blinds installed today. They will cover the back windows and need to be installed next to each other. There were pre-existing blinds there so it would be either using or removing the existing fittings, and then installing the following size blinds (which I’ve purchased from Bunnings and which include screws and brackets): - 90cm - 120cm - 240cm Pictures of space attached. Thanks Penny

4 small gyprock holes to be repaired and ready to paint. Please make me an offer

Door and frame needs fixing up. It blew off the hinges last night in the wind. It's an outside door to a balcony.

I need the tv mounted where an old tv was. The holes to hide the one connector cord already in place. See photos only thing is we need to take out the existing powerpoont behind tv so it's flush to the wall. I'm happy to help so only need one person.

Some black marks and damages on wall and a couple of small holes

install 1 downpipe under box gutter length = 2600mm width = 800mm

We need 5 white fly screens made and installed. We want installer to check the measurements beforehand and additional requirements like clips etc. We want durable fly screens. No openings required. Two measure roughly 78cm wide and 1.9 metres long. Three measure 90cm wide and 1.1 metres.