Find a professional IKEA benchtop contractor in NSW

Looking for a tradesperson / carpenter to install Ikea kitchen bench top in very small 2x2m kitchen. Cabinetry is in place but will require holes cutting for sink and tap. Simple L-shape layout, includes freestanding areas to be supported by legs in place of full cabinets - see reference photo included. Ready to hire and need to complete before Xmas. Potts Point, 2011 - Due date: Before Thursday, 21 December 2023

Hi there, I need someone to drill in 2 metal table legs into a wooden slab that I purchased from IKEA. Thank you very much. It comes with screws, but I don't have any tools to install this. - Due date: Needs to be done on Sunday, 19 November 2023

Cut the bench top in size. You need to bring your own powerful saw as the bench top is thick and strong made of laminated particle wood. Thickness is 2.8 cm - Due date: Needs to be done on Friday, 10 November 2023

IKEA bench but we can’t get the screws to screw fully into the wood. - Due date: Needs to be done on Friday, October 13, 2023

Hi, I’m looking for someone to install IKEA laminate benchtop in Bankstown. The material can be seen on the photos. _Total 3 pieces need to be cut and assemble. 1 x 186cm 2 x 246cm - Due date: Needs to be done on Saturday, 2 September 2023

Building x1 ikea bench, x1 koala bed, x2 easy desks - Due date: Needs to be done on Saturday, 26 August 2023

laminex Benchtop 68 cm X 170 cm Installers - Due date: Flexible

Looking to have 2 x Ikea bench tops cut and fitted on: - 1 x Kitchen benchtop: SÄLJAN wt 246x3.8 oak effect/laminate AP - 1 x Barstation bench top: EKBACKEN wt 246x2.8 matt anthracite/laminate AP - 1 x FÖRBÄTTRA plinth 220x8 matt anthracite AP to be cut and attached next to bar station/ fridge and attach to bench top. - Due date: Flexible

I need to cut a 240 x 90cm IKEA bench top down to 217wide x 55 deep. I believe you will need a track saw. It is located in Newtown and is out the back of a shop which is open 10am to 7pm M-F. - Due date: Flexible

My dog chewed the benchtop corner and I need it fixed. It's a rental and the benchtop is IKEA laminate. There is a lot of bench overhang, so I think someone could cut it back a little and then reapply the edging. - Due date: Before Friday, 5 May 2023

Install benchtop to existing including join and cutouts and fit sink and cooktop in place and any siliconing. Does not include plumbing or electrical work. - View all the details of this offer: https://www.airtasker.com/offers/01GY6J3K1BBRYP0W6X725E0PHH

Hi, I need someone to construct an IKEA kitchen bench (photos below). I think all you’d need is some tools, many thanks. - Due date: Needs to be done on Tuesday, 21 February 2023

I need to replace current laminated kitchen benchtop with IKEA kitchen benchtop. Laminate needs to be cut and holes be made for cooktop and sink. - Due date: Before Tuesday, 11 October 2022

Benchtop size is 180cm x 40cm - Due date: Flexible

need someone to drill ikea legs on to ikea bench.

2 piece Oak Venneer PINNARP) benchtop from Ikea. Cut holes too for Sink and Cooktop. Installed. - Due date: Before Saturday, 23 April 2022

Need to attach and cut ikea bench top around 180cm to an ikea 2 door kitchen cupboard 80cm and attach small legs underneath the cupboard. Will need screws for feet as they have been miss placed.

includes: sink and cooktop cutouts affix benchtops to cabinetry seal all cutouts (especially sink) Waterfall mitre edge - Due date: Before Thursday, 30 June 2022

Hi, we just need someone with the right tools and experience to measure twice and cut once our ikea benchtop, and fit on top of enhet kitchen unit.

Hi - you did a job for some a few years ago. Wondering if you could cut a very small amount off an ikea benchtop (and cut in to fit around window frame). Also cut 60mm hole in bench top for cable duct, and install the two legs.