Find a professional gate installation in East Melbourne

Looking for an experienced handyman or fencing contractor to repair a timber front fence in Surrey Hills. Work required: Replace one broken gate hinge. Reattach the fence panel to the timber post (panel has separated from the post). Repair the cracked bottom timber rail of the fence panel, or replace it if it cannot be repaired. Please see the attached photos for the condition. I've also included a close-up photo of the cracked bottom rail to show its size and condition. I would like the fence and gate restored so they are secure and functioning properly. Please quote for labour only. If replacement materials are required (for example, if the bottom rail cannot be repaired), please discuss this with me first before proceeding. Material costs can be charged separately if agreed.

Electric gate moving slowly. Has happened before in cold weather and condenser needed changing but not sure if if it is the same issue

Install a gate on side of house. Provide gate- steel frame and structure. Dig footings and install including lockable function so secure. I have added an image of the type of gate I need. Please quote for the whole job not excluding materials- full costed job

need an experienced roof plumber or skilled handyperson to resolve a drainage issue on my carport roof. As shown in the attached photos , water is currently getting trapped and pooling significantly on the corrugated metal roofing instead of draining away. Looks like the metal roofing is sagging in the middle then the outer side causing the pooling of water.

Task: Remove Existing Side Gate & Supply and Install New Colourbond Gates Remove existing side gate then then supply and install a new black Colourbond gate system. Scope: • Remove existing gate/fence • Supply and install galvanised steel posts • Supply and Install two matching black gates, metal (colourbond or similar), either solid or vertical posts with minimal gaps • Side gate posts to be 75x75x2mm gal posts, 1.95m in height out of ground to match gate height. • Posts to be set in concrete in post hole, approx 70x80cm deep. • Gates to be hinged off posts. • One gate to have pad bolt to ground, the other gate to have a keyed handle to secure. • Gates to open inward (ie. Towards back of the block) • Approximate width of driveway: 3.5m (building to boundary fence) • Desired height: 1.95m • Ensure gates are level, secure and operate smoothly Easy access. Please include all materials, and labour costs in your quote (disposal of old gates not required). Photos attached.

Footpath. Concrete exposed aggregate.

Rehang heavy gate. Top hinge bolt has snapped and remains embedded in brick. Replace top fixing with suitable heavy-duty masonry/chemical anchor and inspect/replace bottom hinge fixing if worn. Realign latch.

Looking for fence and autogate installation. Fence length about 11 metres mounted on existing retaining wall. Horizontal aluminium slats preferred in monument charcoal. Prefer automatic sliding gate about 4 to 4.5 metres on driveway level.

Looking for an experienced painter to paint an internal corrugated metal wall, as well as the surrounding window and door trims. The corrugated wall is currently unpainted, and the trims are already painted and will require preparation before repainting. I have attached: - A photo of the existing wall and trims - Inspiration photo showing the desired colour scheme (soft pastel yellow lower section and creamy white upper section and pastel tones for the trims). Please provide a quote for labour and advise whether any preparation, priming, or materials are required. Will consult and purchase paint and materials separately. Looking for a neat, professional finish with clean lines and attention to detail. Please review the attached photos and provide your recommended approach and quote.

Have a gate that needs a new hinge put into it. Two hinges, the top one looks ok but have bought another to be put on the bottom. Reasonably heavy gate. Any queries let me know.

My driveway entry gate is not functioning properly and needs attention/service. It’s an automatic sliding gate powered by a Tau K100M motor. See photos. The gate will not open without manual effort as the cog on the motor will not grip on the gate frame (to pull and slide it open). It closes no problem. I have a video that shows this clearly. I’ve examined the parts and there doesn’t appear to be any wear and tear causing this. I suspect it just needs realignment now and then.

Need handyman to help fix outdoor gate. Outdoor gate is slanting, bracket needs reattaching.

Install this baby gate onto brick and wooden post

I have a double swing automatic gate at my driveway. The gate used to operate normally where the right-side gate opens first, followed by the left-side gate after a short delay, so they don’t interfere with each other. Recently, the sequence seems to have changed. The left gate is now trying to open first while the right gate is still closed, which causes the left gate to hit or be blocked by the right gate. Because of this, the gate cannot open properly and the system stops working as expected. It appears the opening sequence or timing between the two motors may be incorrect, or the controller settings may have changed. No physical damages only need proper programming

Gate is not latching as it has moved off the hinges. Need it to be rehung so lock can engage.

I need a repair service for a heavy steel gate. It has pulled away from the rendered concrete pillar and needs to be professionally re-mounted (likely using Chemset anchors for a more secure fix). The gate is intact; it just needs a solid connection back to the masonry.

Task: Repair / re-hang external gate – hinge failure due to wood rot I need a handyman or carpenter to fix the hinges on my external side gate. The gate has a metal frame with vertical wooden battens. One of the hinges has pulled away because the wooden fence post/stud it was fixed to has rotted. Job likely involves removing the gate, repairing or replacing the affected section of timber (or installing a new mounting plate/post), and securely re-attaching or replacing the hinge so the gate opens and closes properly. Gate is outdoors and exposed to weather. Materials and fix should be suitable for exterior use.

Need to collect a stair gate from Bunnings and install it at the top of the stairs

-3.50 meter electric gate to be installed (inside post to inside post) -1.6 m high to match exisiting front fence -any style -need someone who can build electric gates and will have returning future work for them aswell

Need to install two gate latches and remove two existing gate latches which are no longer work on Outdoor exterior wall which is rendered