Find an experienced gas fitter in Sydney

Need a licensed gas fitter to connect a commercial Goldstein gas grill in a restaurant kitchen. The grill is already in place and there is an existing gas line nearby. I need someone to: Connect the grill to the gas supply Check for leaks and test everything safely Make sure it is working correctly and compliant Location: Newtown, Sydney, NSW Please bring the required tools and fittings if needed. Experience with commercial kitchen equipment preferred.

Hello I have a gas burner (the largest burner on the stove) which lights but won't stay lighted, so likely thermocouple issue. Located in Botany. Is this something you fix and if you service the area? Also approx how much to fix problem? Thank you

Hello I have a gas burner (the largest burner on the stove) which lights but won't stay lighted, so likely thermocouple issue. Located in Botany. Is this something you fix and if you service the area? Also approx how much to fix problem? Thank you

I need the existing gas cooker removed and the induction cooker installed. The gas cooker is currently installed to a 10 amp socket. This 10 M socket is less than a metre away from the main power board in the cupboard next to it as new induction would require a high rated power connect.

Install gas conversion kit on beef eater bbq

Turn off gas to the house. Disconnect old gas / gas free-standing oven / stove top. Install and connect new gas/ gas free-standing oven / stove top. Reconnect gas and confirm safe operations.

I have a very small leak from a threaded connection on the household side of the gas meter. I've confirmed with soapy water after smelling the leak for a while. Someone has used lots of white thread tape on it previously.

Gas cooktop - one burner not igniting, others working fine. Ignites with lighter so gas is fine. Likely igniter issue. Quick fix needed.

Need a qualified person to replace a thermocouple in a gas stove. One small burner doesn’t stay on when turned on.

I have a complete portable LPG gas setup for a market stall and need a licensed gasfitter to inspect, leak test, and issue the required compliance certificate/tag so I can trade at Parramatta/Blue Sky Markets. What I already have (all new or in good condition): • Camp Chef Pro 2 two-burner stove with original Australian fittings and ~900mm hose/regulator • Garth Gas Safety Gauge (LCC27) – the “gas fuse” with automatic shut-off, level gauge and leak test function • 9kg LPG bottle (in test date) I just need you to: • Assemble/check the full setup (bottle → Garth gauge → hose/regulator → stove) • Perform a proper leak/pressure test • Issue the official compliance certificate or tag that I can display at the stall This is a quick job — everything is ready to go.

My Smeg gas cooktop (see attached photos) has one burner where the ignitor is now flickering/weak when I turn the knob. It was working perfectly until yesterday when steam from a boil-over on the next burner got into the ignitor area. I’ve already cleaned it with isopropyl alcohol and let it dry for a full day, but the spark is still intermittent and weak. All other burners ignite normally. I’m looking for a quick, reliable fix – either a deep clean of the electrode/spark module or replacement of the ignitor if needed.

Just need my gas cook top looked at a couple the burners turn on then turn off the pilot isn’t staying on at times. Could be a clink or gas blocked

Relocate natural gas bayonet by 1.5m. The bayonet already exists outside and is going to go inside an outdoor kitchen cabinet to be installed afterwards.

Need our gas meter moved up the wall so it sits above the soil which rusted put the previous meter and it leaked.

I need someone to install a gas bayonet in my living room, on a plasterboard wall that is close to the gas pipe (45 cm away). It’s for using a gas heater (Rinnai pocket rocket, similar to Enduro 13). Please see pictures.

We installed a new gas stove and need a gas fitter to verify there are no leaks.

I’m after gas fitter for connecting my commercial stove in my kitchen

Safely and professionally. Must be certified/qualified. Scope of Works – Disconnections for Disposal 1. Safely disconnect and isolate the oven to allow for disposal. 2. Safely disconnect and isolate the gas cooktop to allow for disposal. 3. Disconnect and cap off the kitchen sink taps as required for removal. 4. Disconnect and cap off both bathroom sink taps to enable disposal of the cabinets.

Rebooking task between Jo and Hassan

Hi, I’m looking for a licensed gas fitter to safely disconnect and cap an existing gas cooktop. The cooktop is currently installed and access is clear. Please confirm whether removal and disposal of the existing cooktop is included. The apartment is located in Pyrmont, within a strata building, and parking is provided on site. Looking to have the work done during the week of 29/12 to 03/01 ideally Please let me know your availability and whether a compliance certificate is provided. Thanks!