Find an experienced flooring expert in Melbourne Western Suburbs

Previous owner renovated the laundry area but did not measure properly to fit a washing machine, so they cut out some of the laminate to fit the washing machine. However, my washing machine is slightly bigger and does not fit and need to cut more of the laminate so the washing machine can slide in. Then the washing machine will need to be hooked up.

Need 6-7sqm hybrid flooring installed. Ready to go. Need it done tomorrow.

Vinyl sheet flooring.: I have all materials.. vinyl sheet.I’ve got a walk in wardrobe in my room. All in total my room size is about 3.5 metres long. And width is 2.8.. but anyway.. I’ve got all materials needed for this job/installation to go ahead and be complete. If I’m happy with the job Il need another 3 rooms to be complete. I need it done and complete with in 4 hours tops. Happy to pay $50 buks an hour.: the job needs to be done properly or I will not pay. Needs to be complete with in 3 hours of the time of arrival thanks.

Looking for someone experienced to install decks for the front porch and patio- fix and supply.

"Looking for a reliable handyman lay new vinyl flooring in a small bathroom. Scope of work: Remove existing vinyl flooring and prep the subfloor. Ensure the floor is clean, flat, and level. Install new ""no surface sealer required"" Vinyl that I have already purchased. Neat cuts around the edges, vanity Apply professional-grade, waterproof silicone sealant around the perimeter to prevent leaks. Details: Very small room size: 2m x 1.7m Materials: I have already purchased the vinyl flooring. You will need to bring your own tools and silicone. Location : werribee VIC Please see photos"

Lay a Hybrid Floor, Godfrey Hirst 10mm Boards to one square room just under 18 mtrs...T trim to be installed to 1 and half sides up to existing Tiles with tile edge and remaining 2 and half sides to walls with skirts removed...Blank Canvas as old laminates removed and I will Dispose of Rubbish...Boards and Trim supplied...walk in, walk out....

Replace carpets with wooden or hybrid floors 2 rooms ground level Staircase 1st floor landing passage way

Approx. 45 m² across three carpeted rooms on a concrete slab. Seeking supply and installation of approximately 7 mm hybrid/SPC flooring with at least a 0.5 mm wear layer and integrated underlay. Quote to include: - Removal and disposal of existing carpet, underlay and tack strips - Supply and installation of flooring - Trims/scotia and door transition trims - Minor floor preparation/levelling where reasonably required - Any major levelling or subfloor preparation to be quoted separately and approved before work proceeds Seeking a vinyl/hybrid plank colour similar to the existing beige-grey/natural timber-look flooring already installed in the hallway, bathroom and kitchen. Images included showing the existing carpet and underlay. Please provide the full GST-inclusive Airtasker price upfront, including any allowance you need to make for Airtasker fees. If possible, please also state the flooring brand/range, wear layer and warranty.

Help lay a floating floor in Werribee must have experience

Looking to hire an experienced flooring contractor in Point Cook to supply and install premium hybrid flooring with underlays across 4 bedrooms and a lounge room (~70–75 sqm). The job requires ripping up and disposing of all old carpet and waste materials, along with supplying and installing quality hybrid planks and matching trims/scotia. Please provide an itemised quote breaking down supply versus labour costs, along with details on the board specs (thickness, wear layer) and photos of past work. Flexible on the start date for the right trade.

160 sq m single story house I’ve got the floorboards brand new in boxes to be installed manly on top of ties.

I have 7mm hybrid waterproof flooring with 1.5mm underlay already attached and need it installed in a 3.2m x 3.2m room, including a small built-in closet area. I have attached a picture of the room which is old. The skirting boards are now installed, and I have purchased matching scotia for the edges. I will supply the flooring and scotia. I am looking for an experienced installer who can also supply the small amount of 200-micron builder's plastic/moisture barrier required for installation over the concrete slab. You must have experience installing hybrid flooring and provide all tools and equipment required to complete the job. Please confirm in your offer that the moisture barrier is included and provide your total installation cost.

Install hybrid flooring, 79 square meters. Prefer Arabic speaker. Located in Werribee.

I need to install the 10MM laminate flooring on top on yellow tonge boards. I have already got the flooring and the plastic sheet for the flooring. Just need to install. Total area is about 12sqm. Please quote install rate per Sqm.

Help with removal of old flooring. Clean up and moving stuff around.

Install hybrid flooring. 79 sqm. Hoppers Crossing. Prefer someone who speaks Arabic.

installation of hybrid flooring

Remove carpet and install hybrid floor

Install deck in backyard

Supply and install of laminate flooring. Hope to beat the prices at bunnings for the supply. Need work on removing existing floor tiles. Need quote for both a) with removing existing tiles and b) not removing tiles. See photos attached, need work on the kitchen and living areas only, rooms have timber floors already, total approx 70sqm to cover. Thanks

Prep, sand and stain hardwoods, around 90-95 square metres. Wood in good condition

Floor needs sanding and polishing to restore condition

Repair damaged timber floorboards – Spotswood Description Looking for an experienced timber flooring specialist/carpenter to repair a small section of damaged timber flooring in our kitchen in Spotswood. Approximately two long floorboards have suffered water/moisture damage, with one section deteriorating and giving way. At this stage, we do not want to re-sand and polish the entire house. We’re looking for the best practical repair possible. Ideally we’d like to: * Remove and replace the damaged sections/boards. * Use matching original floorboards taken from a less noticeable area elsewhere in the house (e.g. inside a cupboard/pantry), if practical. * Replace the donor boards with something suitable. * Make the kitchen repair blend in as closely as reasonably possible with the existing floor. * Check the immediate area underneath for any obvious additional damage while the boards are removed. We understand a completely invisible repair may not be possible without sanding the wider floor — we’re just looking for someone experienced who can get the best possible result without refinishing the whole house. Photos available. Happy for you to inspect before commencing. Location: Spotswood VIC 3015. Please let me know your experience with repairing/replacing existing timber floorboards and matching older flooring.

Need to sand and polish the decking at alfresco and front. Refer photos.

I have old floorboard that I would like to get sand and polish the area needed are 3 rooms and 1 hall. Measurement roughly It’s roughly Room 1: 3.8 × 3.7 m Room 2: 3.8 × 2.2 m Room 3: 3. 3.7 × 4.3 m Hall: 1mx11 It will also stain colour yellow before coat it

Floor Sanding and Polishing Small entry,Lounge,kitchen,Hall and one small room.

Sanding and polishing timber floor

Front walkway and entrance merbou deck, needs sanding back and polished

Sand existing timber flooring. •Polish and apply laminate/protective coating. •Blend new and existing flooring where possible 3 bed house plus study, kitchen, dinning and living room

Sand and Polish of timber boards. Please see photos approx 60 Sq/m of area. House is vacant at the moment so looking for works to be started and completed very soon. Location : Laverton

Sand and clear polish to floorboards as per floor plan attached. Total area highlighted in yellow requires sand and polish. Where I have added some blue lines is the area with wear and scratches the rest of the floor is in good condition. Floors are hardwood. House is empty of furniture and ready for the task.

We would like to get someone to give our floorboards a polish to hopefully remove scuff marks and give the floor a visual lift. Living and kitchen area approx 50m squared. I listed $10 for price just to list the job very mindful it will cost more Thanks

Could someone help fix our dining room timber floor- it’s not in good shape I need sanding and polishing plz

1st floor apartment in Williamstown with hardwood flooring. Has gaps and needs to be filled to reduce draft. Flooring needs to be sanded, polished and finished in a walnut colour. 2x bedroom, lounge room, small hallway and staircase

1 room 16 m2 room has already been sanded. Need to finish the job by resin polishing.

Need front and back deck sanded and polished

Need someone to sand and polish floorboards

Light buff of floors and polish in a 3 bedroom townhouse. Boards are floating floorboards and in good condition, they have faded in some areas from sunlight and we want to touch them up prior to sale. Location: Seaholme, VIC Objective: Restore flooring to near-new presentation suitable for sale campaign Buff & Recoat with water based matte polyurethane (good quality) Meals area is 3.3x4.1m, living area is 4.8x5

The space is 85sqm and currently has carpet flooring. We would like to achieve a look similar to this. It is located on the 3rd floor. Under the carpet is a concrete floor. Could you please provide an approximate cost?

POLISH TIMBER FLOORING - dining/living area. Job to be completed this week. Location Melton South

Need someone to sand and refinish the floor.

Looking for an experienced floor sander to sand and refinish approx 70 m² of timber flooring (living + dining) in a two‑bed apartment in Melbourne. Goal: bring floors up to rental standard (durable, even finish, safe for tenants). Scope: - Sand the whole area (approx. 70 m²), including edges - Repair minor issues (nail pops, small gaps, replace/secure loose boards if needed) — please note major replacements will be quoted separately - Fill and prepare joints/holes, tidy jump/transition strips - Apply stain if requested (note any colour options) and 2 x coats of high‑traffic, water‑based polyurethane (or advise best durable finish for rental) - Clean up and remove dust; minimise dust (dust‑extraction preferred) - Leave site ready for tenants (no strong lingering odours) Location & access: Altona North, ground-floor apartment Timing: - Preferred start date: 5th July 2026 - Please include estimated days on site and drying times

Looking for an experienced tradie to fully sand back and properly refinish internal timber stairs. Anytime between 20th and 25th Jan Details: Approx 14 timber treads (including winders) Existing finish is worn on nosings with a few scuffed areas 2 small gouges to be repaired with timber filler Require full sand back to bare timber (not just a light scuff) Refinish with a high-quality stair-grade clear varnish or polyurethane Minimum 3 coats, suitable for stairs (durable, non-yellowing) Materials to be supplied by you and included in the price Clean, tidy job with proper prep and cleanup Please include in your offer: What product/finish you will use (brand + water/oil based) How many coats Estimated timeframe and drying time between coats Examples of similar stair work if available Home is occupied, but I will be out each day, however walls have just begun painted , so clear communication and care with dust and drying is important. I’ll check quotes later today, will reply then.

I need a small section of timber floorboards (doorway area – see photos) sanded back and refinished to match the surrounding treated floorboards as closely as possible. The area was previously covered by tiles and has old adhesive/paint residue and uneven finish. I’m after a professional result that blends in with the existing floor. Scope of work: • Sand back the existing timber boards to bare timber • Remove all residue/old finish • Prepare surface properly (fill if required) • Stain/colour match to existing floorboards • Apply suitable clear protective coat (polyurethane or similar) • Clean up after job • Supply and apply all required materials Details: • Area size: approximately 1100mm x 1100mm • Location: indoor hallway / door threshold • Access is easy • Photos attached Requirements: • Experience with timber floor sanding & finishing • Own tools and materials preferred • Ability to colour match existing floor as close as possible

Seeking someone to buff/polish roughly 40 square metres of floorboards. (Wormy chestnut) Per the floor plan only the hallway and living area. Bedrooms and bathrooms are carpet or tile. Floors were fully sanded back 3 years ago with water based clear coat applied. Floors are in good condition with light scratch marks. I am not seeking perfection. Some marks may remain. But I won’t have a full re-sand done so soon as one was only done 3 years ago. I am seeking quotes. I will remove and replace my own furniture. Thanks