Find trusted local electricians in Outer East Melbourne

Mitsubishi split system installed 2015: Heating doesnt work. Air is lukewarm in the heating mode (temp at 30 c ) Cooling works perfectly . Energy consumption also gradually decreases as airflow temperature drops in heating

Lamps needs repairing the fitting is loose

electrician or handyman with electrian credentials to replace a fuse for the external aircon unit. The external unit is above the garage and will need a ladder to reach.

Need a licensed electrician to relocate a powerpoint and tv aerial to the same wall just have it elevated for a tv and change a downlight at the front of the house. Both PowerPoint and downlight supplied.

Mount and wire a hardwired 3600W outdoor radiant heater (HEATSTRIP Max DCR) on my covered alfresco deck. I have the heater and all mounting hardware on hand — I need it installed and connected in one visit. Scope — mounting: - Hang the heater overhead from the pergola rafter using my supplied stainless chain, D-shackles and screws/pad eyes. - Fix anchor points into the structural rafter (pre-drilled), level the unit at ~2.4m from the floor, hanging horizontal (face down). - Rafter height is ~3.05m. Easy ladder access. - IMPORTANT — hang to resist sway (open-edge deck, wind exposed): use 4 anchor points in roughly a 600 x 600mm square on the rafters, with the chains SPLAYED OUTWARD in a V (not hanging straight down). Scope — electrical: - New dedicated 15A circuit on its own RCBO from the switchboard. Modern DIN board with spare ways and an 80A main — no board upgrade needed. - Weatherproof isolation switch near the heater. - Cable run along the pergola rafter to the heater; connection point offset to the side, not directly behind the unit, with a service loop so chain movement doesn't flex the connection. - Certificate of Electrical Safety (CoES) provided on completion. Details: - Single-phase supply. Heater draws ~15A / 3600W, weighs ~8kg. - Elevated timber deck under a pergola; switchboard is on around 8meters away. Access is doable via roof or under the house. - All mounting hardware supplied by me (chain, D-shackles/quick links, pad eyes, coach screws). Please quote a FIXED PRICE for the complete job — mounting + electrical + isolator + all consumables + CoES — not hourly. Must hold a current Victorian electrical licence (Energy Safe Victoria). Flexible on timing.

LED Strip Installation Required – Quote Request I have a bar unit with three shelves, and each shelf already has an LED channel installed underneath. I'm looking for someone to supply and install warm (yellow tone) LED strip lights in all three channels. Please Note : After the LED being installed,the splash back will be installing. So just keep in mind that the surface needs to be clear for splashback. Please provide your quote including all materials and installation. Thank you.

Replacing or upgrading to down lights (20 (

Change GPOs, switches, batten light and install pendant lights and GPO. There are 5 tasks. Please refer to the attached photos with task descriptions. Batten light product: https://www.voltexelectrical.com.au/p-6735-led-indoor-batten-2nd-gen-multi-power-tri-colour-1-10v-dimmable.aspx Recommend and supply black GPOs, sockets and switches for the garage. Recommend and supply dimmmable switch for bedroom pendant lights. Pendant lights (2x) will be provided.

Simply need 3 pendants replaced with new ones. Must be qualified electrician.

Fixed hourly rate. Put a lock on a door, change an outdoor light to a sensor. Install a battery sensor light. Check a power point to see why it's not working.

I would like to get an electrician to replacement for 2 Hard wired smoke alarms. The current alarm is too old. Flexible with time but need to be this week.

Have a number of small electrical jobs starting with disconnecting power to a garage and external power board made safe (just purchased the house and looks like a home handyman job)

Need an electrician ASAP, to remove 2 old hardwired smoke alarms and provide 2 new smoke alarms and install them please. Anytime before 12pm

Need a power point to toilet

Please help me light my pilot light of my gas water heater.

I am looking for a quotation to install 4 downlights and replacing a ceiling fan in our master bedroom. I will provide the downlights and new fan and other wiring if needed.

Hi there, I am currently doing some home renovations and need a licensed electrician to update the connections for 5 existing LED wall lights. Current situation: There are 5 old LED wall lights (70mm cut-out). Their LED drivers are currently hardwired into the mains behind the plasterboard. What I need you to do: • Remove and safely disconnect the 5 old hardwired LED drivers. • Supply and install 5 standard surface sockets (plug bases, e.g., Clipsal 413 or similar) at these existing points. • Push the new sockets back into the wall/ceiling cavity safely. Important details: • No new wiring or cutting new holes is required. The 70mm holes and the wiring are already there. • I will supply and plug in the new downlights myself once the sockets are ready. You only need to supply and install the 5 surface sockets. • You must be a fully Licensed Electrician and be able to provide a Certificate of Electrical Safety (COES) upon completion. Please let me know your availability and your quote for the complete job (including the supply of the 5 sockets). Flexible with dates but prefer to get it done soon. Thanks!