Find trusted local electricians in Sydney Northern Beaches

Disconnection of existing lounge A/C system.Installation of Mitsubishi Electric multi head A/C system serving lounge and bedroom. Unit sourced Lounge: 5Kw wall mounted indoor unit Bedroom: 2.5Kw wall mounted indoor unit Outdoor unit: 5.2Kw reverse cycle inverter multi head outdoor unit MXZ-2F52VF-A1. Colorbond trunking to be replaced with larger trunking to accommodate new bedroom piping/ wiring (this will be supplied) Electrical: New dedicated A/C electrical power circuit with outdoor isolation switch and safety switch as required (supplied). Internal cable duct will be required to run mains from internal DC to outdoor circuit breaker.

Replace with a light switch and fan knob on the one switch. Currently the fan switch does nothing. Fan operates by turning knob. Switch above controls the light.

Must install today - after 3pm Have purchased fan - see pic

I’m attempting to wire up new headlight, Speedo, odometer, indicators and tailight on a 2006 Yamaha TW200. Need some assistance!

House has old style light needs to replace ansd ffew more down lights

Fix outdoor front, side and back sensor light, and potentially set up new side light in back

I Need a licensed electrician to fit two double GPOs inside an existing wall mounted shaving cabinet in a bathroom. All the prep is done: - Cabinet is installed and fixed to the wall - Cut-outs already made in the cabinet back panel - Cables (TPS) already run and pulled through, ready to terminate - Outlets and mounting brackets are on site no materials needed Scope is purely termination and fit off: mount the brackets, terminate the outlets, secure them neatly, test and make good. Should be well under an hour for someone with the right gear. Requirements: - Current NSW electrical licence (please include your licence number when quoting) - Certificate of Compliance for Electrical Work (CCEW) provided on completion Location: Dee Why.

I need 5 lights swapped out with remote controlled ceiling fans. 4 are in same location and 1 will need to move about 500mm I have a lot of other renovation jobs that can be discussed in person

Electrician needed to change 2 of these lights. Need to provide the light yourself and we reimburse you the cost of buying the replacement. ASAL SINGLE CIRCUIT LED TRACK LIGHT CODE: STR9017/15TC/BK 2 PCS.

Need light fitting reattached to ceiling

Install a Samsung 9kg Heat Pump Smart Dryer and remove old one,

Repair mitsubishi hyper inverter split air-conditioning SRK71ZRA-W. It works and switches on with heater function working however pauses with no air blowing (still powered on and vents open) after 15- 30 minutes with timer light flashing 5 times continously. Timer is definelty off and I've reset the remote and also switched off the main power at the meter to reset the unit but still occurs. Ive already had an electrian check out the meter box to see if this as result of an overload which is not. Not under warranty

Need a licensed electrician to wire up three ceiling exhaust fans across three bathrooms. Electrical work only — fans are already supplied and on site, ceiling openings are already cut, and ducting/external venting is being handled separately. Scope: Connect and mount all 3 fans (standard ducted ceiling exhaust fans, supplied with flex lead and plug). Each fan needs its own dedicated wall switch, separate from the existing light switch. Happy for you to add a switch to the existing light switch plate if that's neatest — please advise, and note if the plate needs replacing to fit an extra switch. Test and leave tidy. Ducting and external venting are not part of this job. Certificate of Compliance for Electrical Work (CCEW) on completion. Access — please read carefully before quoting. All three runs are tight: Bathrooms 1 and 2 — ground floor of a two-storey house. No roof space above. Cabling must be fished through the inter-floor cavity (between ground floor ceiling and first floor flooring). Bathroom 3 — single-storey section with a metal (colorbond) roof. Roof cavity is only around 30cm between the ceiling and the roof sheeting, so it is not walkable — cabling will need to be fished rather than crawled. All ceiling openings are already cut. Please include in your offer: Your NSW electrical licence number Confirmation you're comfortable with tight-cavity cable runs (this is the bulk of the job) Whether the price includes switch plates and any wall patching if chasing is needed

Looking for a licensed electrician for a few small jobs in one visit: 1. Replace 2 existing wall sconces with new light fittings (new fittings will be supplied) 2. Install a new backlit mirror (power connection required) 3. Fix a double power point – one socket isn’t switching on All fittings/fixtures will be on-site and ready to go. Looking for someone with the right licence/certification who can provide a compliance certificate if needed. Category: Electrical Location: Allambie Heights, NSW 2100 When: Flexible – within the next week Budget: $300

We're looking for a licensed electrician to install a new power point above our shelving. The cable can be run down from the ceiling cavity directly above, so it should be a straightforward installation. We expect the job to take around an hour, and our budget is approximately $500. Please send through your offers. **Licensed electricians only, please** Thanks!

I have 4 external lights that I need installed - too replace exisiting lights. All wiring is in place. And lights need to be fixed to brick veneer.

Hi there, We just moved into a new rental and it looks like the black plastic insert for our hanging light is broken as it kept pushing out the light bulb. Need the insert to be replaced as don’t know how to do myself.

Looking for an electrician to complete a small residential job in my apartment. The apartment was built around 2000, so the wiring is relatively modern and I don’t anticipate any major issues. Work required: Light switches and power points + two LED lights replaced, includes - * Replace 11 × double power points * Replace 1 × quad power point * Replace 6 × single light switches * Replace 1 × two gang light switch * Install 2 × two gang LED dimmer/switch combinations * Might need 1 × surface mounting block (bathroom) * Install 2 × new Martec Fino LED ceiling lights, replacing two existing LED ceiling lights (same locations, pretty much the same lights just a bit bigger, no new wiring required ect) I will supply everything, it’s Clipsal Iconic and I think the old ones are HMP: * Clipsal Iconic switches and power points * Martec Fino LED lights * Dimmers * Mounting block I’m looking for: * Licensed and insured electrician * Neat, professional installation * Experience installing Clipsal Iconic products and LED dimmers Preferred, not necessary though Photos of the existing switches, power points and lights can be provided if needed

Scope: Disconnect existing damaged glass cooktop, wire in and install the new replacement unit. Benchtop Cutout: No cutting or modifications required. The new cooktop is an exact size replacement for the existing cutout. Materials: I have already purchased the new Westinghouse cooktop. You will just need to supply your standard tools and any minor electrical consumables (wire connectors, etc.) if required. Disposal: Please include the removal and disposal of the old broken cooktop in your quote. (Alternatively: I will handle the disposal of the old unit myself.) Requirements: Must be a fully licensed electrician and able to provide a Certificate of Electrical Safety / Compliance upon completion. Please bring your own tools and safety gear. unit is: WHC643BE

Please only licensed electricians bid on this job. Please include materials in your bid. Job description: Replace 1 halogen light with a standard LED down light. I have included a photo of the general down light we are after. An iron caused a fuse to blow and the light has blown. The other switch on the same switch still works. There is no rush for this job although we are aiming to have it completed this week, 8th-14th June. Please send any questions you have. Thank you.