Find trusted local electricians in Outer East Melbourne

Install power point/s for outdoor electric blinds

Electrical compliance check in the whole house and install exhaust fans in Bathroom and laundry.

Job to connect power for kitchen reno & ensure everything is safe for compliance and standards. 1 hour work required only.

Roll a steel wire mesh around solar panels on the roof, and clip the mesh to the panel frames. Only some pliers required and a ladder. The mesh material and clips provided. No requirement to touch wiring or anything electrical - just need to be able to work safely at heights.

I need switch board replaced in my restaurant one of the switch doesn’t work properly

I need an old aircon unit hole plaster boarded (roughly 67cm x 45cm )as well as a small old electrical power hole plaster boarded (roughly 10cm x 10cm). Aircon unit will be removed by myself prior to job and electrical power has already been removed.

I have restored a new garden shed , power points were removed during building , the existing wiring used to connect to old shed is still there, I need a qualified electrician to set up power points in the garden shed , please provide me estimate quotation

3 spilt Air con head units to be cleaned.

Need to replace the 8 down lights Dimmable lights - 6 Normal - 2

Need to have power connected for a Spa - 32 amp direct to switch board Power connection for a Water tank pump

Install three ceiling fans DC with remote controls (fans likely don’t need roof access as fans already exist in the same spot) and additional electrical wiring added at three different points in the house for the install of Arlo cameras

Lighting Works (Quantities Included) Downlights 21 × NEW LED downlights (new cut-outs & wiring) 14 × LED downlights to replace existing halogen fittings Total LED downlights after works: 35 Oversized retrofit trims required where replacing halogen cut-outs Other Lighting 4 × LED linear / channel lights (replace existing in pool room) 2 × Bedside wall lights (master bedroom) Light Removals 2 × Pendant lights (study & dining) 1 × Wall light (entrance) 1 × Fluorescent tube light (kitchen) Switching 9 × LED-compatible trailing-edge dimmer switches Includes isolation, disconnection, and removal of existing switches Reuse existing switches only where specified Additional Electrical Works 1 × New double power point in garage 1 × Main switchboard upgrade (RCD/RCBOs as required) Technical Requirements LED downlights: 3000K warm white CRI ≥ 90 IC-4 rated Visually consistent trim style throughout Ceiling make-good: patch only, no painting All removed fittings to be disposed of Works to comply with AS/NZS 3000 Electrical Certificate of Compliance required

I need Electrician to change some lights and switches in two bathrooms First Bathroom - one room has become two rooms, additional switch and light, fan heat light in the new room, Second bathroom, two rules have been combined and one switch is required, light fittings supplied by me, Replacement of free in one heater light and fan, relocation of another fan,

10 downlights for three bedrooms and a hallway area upstairs. And remove old lights. Price with and without dimmers in rooms please.

Recently completed plaster ceiling & need to install 3 x LED downlight.

Bedroom ceiling light on, with switch on or off. Wiring to ceiling light to check and correct

Need an electrician to do the following 1. Replace old fans with the new one in 2 rooms 4. Replace 4 down lights in the dining room. We already have the new fans and the down lights. Please check the photos.

I need a qualified electrician/data technician for the following tasks: 1. TV Power & Cabling • The TV is already wall-mounted, but the existing power points located below the TV need to be removed. • There is a power outlet behind the TV that currently sits in an oversized hole. I have a recessed outlet that needs to be installed there. 2. Additional Power Outlet • Install one new power outlet inside the small under-stair storage area. 3. Data Cabling • Run two Ethernet cables, both terminating in the server cabinet: • One cable from the front door to the server (for a doorbell). • One cable from the garage to the server (for a security camera). 4. Faceplate Installation • Install three recessed faceplates (already provided). These require extra depth, so space behind them may need to be adjusted. 5. Pendant Light • Lower the existing pendant light to the desired height.

Install a new smoke detector in the hall way

I have got a 20 amp single power point and I'm wondering if it can be changed to a 10 amp double power point. Should be a quick job. Looking for a licensed electrician