Find trusted local electricians in QLD

This ceiling wiring needs to be brought up to date as it currently outputs a female “SM 2 Pin Plug”. The replacement Downlight pictured connects to a power outlet, so assuming the wiring needs to be updated to a power outlet.

I have a Solahart solar hot water system with an electric booster. The booster doesn’t seem to be working (water not heating as expected). Looking for a licensed electrician to: Inspect the booster system Check wiring, thermostat, heating element, and connections Identify the issue and advise on repair Requirements: Must be a licensed electrician (QLD) Experience with hot water systems preferred Please include your license number in the offer Location: Bellbowrie Timing: Flexible (prefer sooner) Please quote for inspection/ diagnosis.Repair can be discussed afterwards

1. Frame and erect 3 walls for art room. 2 of 3000 x 2600, 1 of 6000 x 2600. One 3000 wall has an 1800 x 1800 window to be fitted in. The other 3000 wall has a 1035 x 2040 set of French doors to be fitted. 2. Frame and erect bedroom front walls. Bedroom 1: wall measuring 4505 with a 920 x 2040 cavity doorway (cavity slider frame supplied. Cavity slider is steel frame). Frame front of built in wardrobe measuring 3850 x 3000 (approx.) Bedroom 2: wall measuring 2840 with an 820 x 2040 cavity doorway (cavity slider frame supplied. Cavity slider is steel frame). Doorway to be framed 600mm deep] Frame built in wardrobes – each side of doorway. One measuring 610mm x unsure of height as angle to meet ceiling) the other side is 1245 x 2700 angled to 2900 (approx) Both walls are 2700 at one end angled to 3450 (raked/cathedral ceiling) 3. Frame bathroom walls x 2 measuring wall 1: 2810 x 3200 (approx.) with a 920 x 2040 cavity doorway (cavity slider frame supplied. Cavity slider is steel frame). Wall 2. 2925mm x 2700 angled to 3200 (approx.) Bathroom also requires a small wall of 640mm x 2900 (approx.) (creates shower wall and other side is cabinet for washing machine etc) I've also attached a plan of the walls. All the outer walls are already done except the 3 outer walls of the art room. The colourbond siding on the wall that will be the bedroom/art room adjoining wall need to be removed and placed on the outer side of the opposite wall of art room.

In unit lights are working but plugs went off suddenly , moved inn new and already connected new energy provider they told need to get electrician, contacted energx same answer ,we also checked safety switch but could be some wiring Issue or something to press in smart meter It’s old style boards Easy to access anytime flexible

Hi, I have a small job to install weather proof outdoor power point and connect plug at the other end of the cable. Material is an available. Looking for services.

Tesla wall charger is two years old and presenting an error today. Blinking red light with green light streaming. Three blinking red lights when just on the charge. Have tried resetting the circuit breaker, and the other troubleshooting online. The guide recommends a qualified electrician. Is connected to 3 phase power.

Need to get battery replaced for a wired smoke alarm that’s beeping at a constant interval.

Require two power points to be disconnected and then reconnected / fixed to a timber panel head board No wiring required.

Remove and replace fluorescent starter and bulb in kitchen light fitting. The ceilings are high. Possibly need electrical experience as the starter has become stuck in the fixture

I have a LED sign board that needs wiring up to the mains power

Two downlights to be changed to new downlights, its 120mm downlight need to be changed to standard downlight.

There are old light replaced with new lights, old lights is removed and there are holes on the ceiling, thise ceilings needs to be patched and colored.There are around 14 holes.

HI Taskers – I need two vintage lamps re-wired and checked over. They currently have American plugs so need to fix that. Also one has a bulb mount that needs to be re-mounted.

Swap old for new appliances installed in kitchen. Existing wiring/powerpoints already there, no movements. 1) induction cooktop Electrolux EHI635BF (existing wire, switch too) 2) oven electric Westinghouse WVE6516DD (existing wire) 3) rangehood Westinghouse WRR604SB (existing plug in PowerPoint) Looking to get job done either Friday 1 may afternoon (from 2pm) or Saturday 2 may morning (finish before 1130am). Pics of current set up, new appliances. Please reply with price and availability. Based in Taigum (5 mins from Westfield chermside).

Licensed Electrician Needed – Riverhills QLD We have a vacant 2‑storey townhouse in Riverhills and require a licensed electrician to: - Remove 14 existing direct‑wired fittings - Supply and install 14 plug bases into the existing 90mm ceiling holes Timing: Work must be completed before Monday 4th May. Only reliable, careful trades please. If you’re available and able to assist, please reach out. Thanks, Rachel & Tim

Hi taskers – I need someone to do a few odd-jobs around my house. Hang a heavy mirror; hang some paintings; rewire 2 x lamps; repair 2 x swivel chairs; and install a divider / curtain into a wardrobe

Our front lights trip the lighting circuit when turned on. There are two lights in the garden which I think it probably is. If necessary they can be disconnected.

Just need new GPO installed, existing one not working due to age. Have the new one here so literally just the labour.

seeking an electrician to fix a new plug point on a electricity cable. previous LED fixture not working and needs to be replaced with a new one. One the cable is fixed deep in the roof, a new socket is required to fix the new LED light.

I'm looking to get a smoke alarm professional to do a smoke alarm compliance certificate as I am selling my home. Looking to get this done ASAP.